1008HQ-39NXGLC Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Chip Inductors - 1008HQ (2520)

Document 190-1
Chip Inductors – 1008HQ (2520)
• Highest Q factors of any Coilcraft chip this body size, roughly
20% higher than our popular 1008CS and HS parts.
• Exceptional SRFs, tight tolerance and batch consistency
Coilcraft Designer’s Kit C323 contains samples of all
5% inductance tolerance parts. Kits with 2% tolerance
are also available. To order, contact Coilcraft or purchase
on-line at http://order.coilcraft.com.

  _{Part number}1
1008HQ-3N0X_L_²
1008HQ-4N1X_L_
1008HQ-7N8X_L_²
1008HQ-10NX_L_
1008HQ-12NX_L_
1008HQ-18NX_L_
1008HQ-22NX_L_
1008HQ-33NX_L_
1008HQ-36NX_L_
1008HQ-39NX_L_
1008HQ-47NX_L_
1008HQ-56NX_L_
1008HQ-68NX_L_
1008HQ-82NX_L_
1008HQ-R10X_L_
  _Inductance3
(nH)
3.0 @ 50 MHz
4.1 @ 50 MHz
7.8 @ 50 MHz
10 @ 50 MHz
12 @ 50 MHz
18 @ 50 MHz
22 @ 50 MHz
33 @ 50 MHz
36 @ 50 MHz
39 @ 50 MHz
47 @ 50 MHz
56 @ 50 MHz
68 @ 50 MHz
82 @ 50 MHz
100 @ 50 MHz
Percent ^  SRF min⁶
  _tolerance4
Q min⁵
(GHz)
5
70 @ 1500 MHz
8.10
5
75 @ 1500 MHz
6.20
5
75 @ 500 MHz
3.80
5,2
60 @ 500 MHz
3.60
5,2
70 @ 500 MHz
2.80
5,2,1
62 @ 350 MHz
2.70
5,2
62 @ 350 MHz
2.05
5,2
75 @ 350 MHz
1.70
5,2
65 @ 350 MHz
1.40
5,2
75 @ 350 MHz
1.30
5,2,1
75 @ 350 MHz
1.45
5,2,1
75 @ 350 MHz
1.23
5,2,1
80 @ 350 MHz
1.15
5,2
80 @ 350 MHz
1.06
5,2
62 @ 350 MHz
0.82
  _{DCR max}7
(Ohms)
0.04
0.05
0.05
0.06
0.06
0.07
0.07
0.09
0.09
0.09
0.12
0.12
0.13
0.16
0.16
  _Irms8
(A)
1.6
1.6
1.6
1.6
1.5
1.4
1.4
1.3
1.3
1.3
1.2
1.2
1.1
1.1
1.0
1. When ordering, specify tolerance, termination and packaging codes:
1008HQ-R10XGLC
Tolerance: F = 1%  G = 2%  J = 5%
(Table shows stock tolerances in bold.)
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape Factory order only, not stocked (7500 parts
per full reel).
2. Part is wound on low profile coilform.
3. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/
HP 4286A impedance analyzer with Coilcraft-provided correlation
pieces.
4. Tolerances in bold are stocked for immediate shipment.
5. Q measured using an Agilent/HP 4291A with an Agilent/HP 16193 test
fixture.
6. For SRF less than 6 GHz, measured using an Agilent/HP 8753D network
analyzer and a Coilcraft SMD-D test fixture. For SRF greater than
6 GHz, measured using an Agilent/HP 8722ES network analyzer and a
Coilcraft SMD­‑D test fixture.
7. DCR measured on a Cambridge Technology micro-ohmmeter and a
Coilcraft CCF840 test fixture.
8. Current that causes a 15°C temperature rise from 25°C ambient.
9. Electrical specifications at 25°C.
For part marking data, visit http://www.coilcraft.com/colrcode.cfm.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Core material Ceramic
Terminations  RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight  32.4 – 35.7 mg;   17.1 – 17.7 mg (Low profile parts)
Ambient temperature  –40°C to +125°C with Irms current, +125°C
to +140°C with derated current
Storage temperature  Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +25 to +125 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging  2000/7″ reel; 7500/13″ reel
Standard height parts:  Plastic tape:  8 mm wide, 0.23 mm thick,
4 mm pocket spacing, 1.8 mm pocket depth
Low profile parts:  Plastic tape:  8 mm wide, 0.3 mm thick,
4 mm pocket spacing, 1.6 mm pocket depth
PCB washing  Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 190-1  Revised 01/18/12
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.