1008CT-900XGLC Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Chip Inductors – 1008CT (2520)

Document 102-1
Chip Inductors – 1008CT (2520)
The 0.055″ profile makes these parts ideal for low clear-
ance applications. Their simple construction ensures
high reliability and stability, and they feature much higher
SRF values than ferrite alternatives. For free evaluation
samples, visit www.coilcraft.com or contact Coilcraft.

Part number¹
1008CT-040XJL_
1008CT-080X_L_
1008CT-100XJL_
1008CT-150X_L_
1008CT-200X_L_
1008CT-300X_L_
1008CT-400X_L_
1008CT-500X_L_
1008CT-600X_L_
1008CT-700X_L_
1008CT-800X_L_
1008CT-900X_L_
1008CT-101X_L_
  _Inductance2
(nH)
4.7 @ 50 MHz
8.2 @ 50 MHz
10 @ 50 MHz
15 @ 50 MHz
20 @ 50 MHz
30 @ 50 MHz
40 @ 50 MHz
50 @ 50 MHz
60 @ 50 MHz
70 @ 50 MHz
80 @ 50 MHz
90 @ 50 MHz
100 @ 50 MHz
  _Percent3   _{SRF min}5
tolerance
Q min⁴
(MHz)
5
28 @ 500 MHz
7500
5,2
40 @ 500 MHz
5000
5
40 @ 500 MHz
2700
5,2
40 @ 500 MHz
3000
5,2
50 @ 500 MHz
2400
5,2
5,2
5,2
5,2,1
5,2,1
50 @ 500 MHz
60 @ 500 MHz
60 @ 500 MHz
60 @ 500 MHz
60 @ 500 MHz
2400
2000
1900
1800
1700
5,2,1
5,2
5,2
60 @ 500 MHz
65 @ 500 MHz
60 @ 500 MHz
1400
1400
1000
  _{DCR max}6
(Ohms)
0.15
0.22
0.25
0.22
0.33
0.38
0.43
0.48
0.52
0.55
0.56
0.61
0.63
  _Irms7
(mA)
600
600
600
600
600
600
600
600
600
510
510
500
480
1. When ordering, specify tolerance, termination and packaging codes:
1008CT-101XJLC
Tolerance: F = 1%  G = 2%  J = 5%
(Table shows stock tolerances in bold.)
Termination: L = RoHS compliant silver-palladium-platinum-glass frit.
E = Halogen free component. RoHS compliant silver-
palladium-platinum-glass frit terminations.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging:
C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
D = 13″ machine-ready reel. EIA-481 embossed plastic
tape (7500 parts per full reel).
2. Inductance measured using a Coilcraft SMD-A fixture in an Agilent/HP
4286A impedance analyzer with Coilcraft-provided correlation pieces.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at using an Agilent/HP 4291A with an Agilent/HP 16193
test fixture.
5. SRF measured using an Agilent/HP 8720D network analyzer and a
Coilcraft SMD‑D test fixture.
6. DCR measured on a Cambridge Technology micro-ohmmeter and a
Coilcraft CCF840 test fixture.
7. Current that causes a 15°C temperature rise from 25°C ambient.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Core material Ceramic
Environmental  RoHS compliant, halogen free optional
Terminations  RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight  17.8 – 17.8 mg
Ambient temperature  –40°C to +125°C with Irms current, +125°C
to +140°C with derated current
Storage temperature  Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +25 to +125 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging  2000/7″reel; 7500/13″ reel  Plastic tape:  8 mm wide,
0.3 mm thick, 4 mm pocket spacing, 1.6 mm pocket depth
PCB washing  Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 102-1  Revised 01/18/12
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.