|
1008AF Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Chip Inductors | |||
|
Document 578-1
Chip Inductors â 1008AF (2520)
⢠Lowest DCR and highest current rating of our 1008 size
inductors
⢠Available in 14 inductance values from 0.9 to 10 µH.
Request free evaluation samples by contacting Coilcraft
or visiting www.coilcraft.com.
â Part number1
1008AF-901X_L_
1008AF-112X_L_
1008AF-132X_L_
1008AF-152X_L_
1008AF-192X_L_
1008AF-222X_L_
1008AF-272X_L_
1008AF-332X_L_
1008AF-392X_L_
1008AF-472X_L_
1008AF-582X_L_
1008AF-682X_L_
1008AF-822X_L_
1008AF-103X_L_
â Inductance2
(µH)
0.9
1.1
1.3
1.5
1.9
2.2
2.7
3.3
3.9
4.7
5.8
6.8
8.2
10.0
Percent
â tolerance3 â Q typ4
10,5
25
10,5
24
10,5
37
10,5
22
10,5
29
10,5
21
10,5
22
10,5
21
10,5
21
10,5
27
10,5
21
10,5
20
10,5
20
10,5
22
â SRF min5
(MHz)
415
376
198
135
126
106
70
59
55
48
37
33
34
26
â DCR max6
(Ohms)
0.100
0.105
0.110
0.125
0.140
0.155
0.190
0.210
0.220
0.435
0.280
0.315
0.395
0.480
â Isat7
(A)
1.4
1.3
1.2
1.1
1.0
0.95
0.80
0.75
0.70
0.70
0.55
0.50
0.50
0.45
â Irms8
(A)
1.3
1.2
1.1
1.0
1.0
0.95
0.90
0.80
0.80
0.65
0.75
0.70
0.65
0.55
1. When ordering, specify tolerance, termination and packaging codes:
1008AF-103XJLC
Tolerance: J = 5%â K = 10%
(Table shows stock tolerances in bold.)
Termination: L = RoHS compliant silver-palladium-platinum-glass
frit. Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging: C = 7â³ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter C instead.
D = 13â³ machine-ready reel. EIA-481 embossed plastic
tape. Factory order only, not stocked (7500 parts per
full reel).
2. Inductance measured at 2.5 MHz using Coilcraft SMD-A fixture in an
Agilent/HP 4286A impedance analyzer with Coilcraft-provided correla-
tion pieces.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at 2.5 MHz using an Agilent/HP 4291A with an Agilent/HP
16193 test fixture.
5. SRF measured using an Agilent/HP 8753D network analyzer with a
Coilcraft SMD-D fixture.
6. DCR measured on a Cambridge Technology Micro-ohmmeter.
7. DC current at 25°C that causes an inductance drop of 10% (typ) from its
value without current. Click for temperature derating information.
8. Current that causes a 40°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute maxi-
mum ratings. Click for temperature derating information.
9. Electrical specifications at 25°C.
Refer to Doc 362 âSoldering Surface Mount Componentsâ before soldering.
For part marking data, visit http://www.coilcraft.com/colrcode.cfm.
Designerâs Kit C414 contains 10 of each 5% value
Core materialâFerrite
Terminationsâ RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weightâ 28 â 33 mg
Ambient temperatureâ â40°C to +85°C with Irms current.
Maximum part temperatureâ +125°C (ambient + temp rise). Derating.
Storage temperatureâ Component: â40°C to +125°C.
Tape and reel packaging: â40°C to +80°C
Resistance to soldering heatâ Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)â +100 to +350 ppm/°C
Moisture Sensitivity Level (MSL)â 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packagingâ 2000 per 7â³reel; 7500 per 13â³ reel
Plastic tape:â 8 mm wide, 0.3 mm thick, 4 mm pocket spacing,
2.0 mm pocket depth
PCB washingâ Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 578-1â Revised 10/12/15
|
▷ |