0906-2KL Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Micro Spring™ Air Core Inductors

Document 163-1
Micro Spring^™ Air Core Inductors
• Small air core inductors feature high Q and tight tolerances
• Acrylic jacket provides a flat top for pick and place
• Solder coated leads ensure reliable soldering
Part
number¹ Turns
0906-2KL_ 2
0906-3JL_ 3
0906-4_L_ 4
0906-5_L_ 5
1606-6_L_ 6
1606-7_L_ 7
1606-8_L_ 8
1606-9_L_ 9
1606-10_L_ 10
L²
(nH)
1.65
2.55
3.85
5.40
5.60
7.15
8.80
9.85
12.55
Percent Q⁴
tol³ min
10 100
5 100
5,2 100
5,2 100
5,2 100
5,2 100
5,2 100
5,2 100
5,2 100
SRF DCR
min⁵ max⁶ Irms⁷
(GHz) (mOhm) (A)
10.0 4.0 1.6
8.2 5.0 1.6
7.5 6.0 1.6
7.0 8.0 1.6
6.5 9.0 1.6
6.0 10 1.6
6.0 12 1.6
5.2 13 1.6
4.6 14 1.6
1. When ordering, specify tolerance, termination and packaging codes:
Terminations RoHS compliant tin-silver over copper Other
terminations available at additional cost.
Weight 0906: 10 –12 mg; 1606: 18 –27 mg
Ambient temperature –40°C to +125°C with Irms current, +125°C
to +140°C with derated current
Storage temperature Component: –40°C to +140°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL) +5 to +70 ppm/°C
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging 0906: 500 per 7″ reel Plastic tape: 8 mm wide, 0.3 mm
thick, 4 mm pocket spacing, 1.5 mm pocket depth
1606: 500 per 7″ reel Plastic tape: 12 mm wide, 0.3 mm thick, 4 mm
pocket spacing, 1.6 mm pocket depth
PCB washing Only pure water or alcohol recommended
A
D
Encapsulant
E
C
Size
0906
B
A max B max C max
0.095 0.135 0.060
2,41 3,43 1,52
D
0.055 ±0.010
1,40 ±0,25
F
E
F max
0.072 ±0.010 0.020
1,83 ±0,25 0,51
1606-10GLC
Tolerance: G = 2% J = 5% K = 10% (Table shows stock
tolerances in bold.)
Termination: L = RoHS compliant tin-silver (96.5/3.5) over copper.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape, 500 parts per full reel.
B = Less than full reel. In tape, but not machine-ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
2. Inductance measured using Agilent/HP 4286 with Coilcraft SMD-A
fixture and correlation.
3. Tolerances in bold are stocked for immediate shipment.
4. Q measured at 800 MHz, using an Agilent/HP 4291A with an Agilent/
HP 16193A test fixture.
5. SRF measured using an Agilent/HP 8720D with a Coilcraft SMD-D fixture.
6. DCR tested on the Cambridge Technology Model 510 Micro-ohmmeter.
7. Current that causes a 15°C temperature rise from 25°C ambient.
8. Electrical specifications at 25°C.
See Qualification Standards section for environmental and test data.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
1606 0.165 0.135 0.062 0.055 ±0.010 0.144 ±0.012 0.020
4,19 3,43 1,58
1,40 ±0,25
3,66 ±0,30 0,51
135°
Strip max
Length
0° min
Recommended Land Patterns
0906 Size
0.031
0,79
1606 Size
0.031
0,79
0.040
1,02
0.097
2,46
0.040
1,02
0.097
2,46
0.072
1,83
0.144
3,66
Dimensions are in
inches
mm
Specifications subject to change without notice.
Please check our website for latest information.
Document 163-1 Revised 10/29/08
© Coilcraft, Inc. 2009