0805AF Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Ferrite Chip Inductors – 0805AF

Document 781-1
Ferrite Chip Inductors – 0805AF (2012)
• Higher inductance values than ceramic 0805 inductors • Heavier guage wire for low DCR
• Inductance values from 0.11 µH to 22 µH
• Ferrite construction for high current handling
 Inductance²
  _{Part number}1
±5% (µH)  Q typ³
0805AF-111XJR_
0805AF-681XJR_
0805AF-102XJR_
0805AF-122XJR_
0805AF-152XJR_
0.11 @ 7.9 MHz
0.68 @ 7.9 MHz
1.0 @ 7.9 MHz
1.2 @ 7.9 MHz
1.5 @ 7.9 MHz
18 @ 7.9 MHz
19 @ 7.9 MHz
17 @ 7.9 MHz
19 @ 7.9 MHz
20 @ 7.9 MHz
0805AF-182XJR_
0805AF-222XJR_
0805AF-272XJR_
0805AF-332XJR_
0805AF-472XJR_
1.8 @ 7.9 MHz
2.2 @ 7.9 MHz
2.7 @ 7.9 MHz
3.3 @ 7.9 MHz
4.7 @ 7.9 MHz
20 @ 7.9 MHz
19 @ 7.9 MHz
19 @ 7.9 MHz
19 @ 7.9 MHz
18 @ 7.9 MHz
0805AF-682XJR_
0805AF-103XJR_
0805AF-153XJR_
0805AF-223XJR_
6.8 @ 7.9 MHz
10 @ 2.5 MHz
15 @ 2.5 MHz
22 @ 2.5 MHz
18 @ 7.9 MHz
18 @ 2.5 MHz
17 @ 2.5 MHz
17 @ 2.5 MHz
Impedance typ
(Ohms)
370 @ 500MHz
430 @ 100 MHz
670 @ 100 MHz
860 @ 100 MHz
1000 @ 100 MHz
1360 @ 100 MHz
840 @ 50 MHz
1050 @ 50MHz
1670 @ 50 MHz
950 @ 25 MHz
450 @ 10MHz
740 @ 10 MHz
1300 @ 10MHz
1620 @ 10 MHz
  _{ SRF typ}4 _{ DCR max}5 _{  Irms}6
(MHz)
(Ohms)
(mA)
1260
425
355
375
285
0.05
940
0.30
660
0.39
650
0.64
440
0.74
390
300
0.98
370
105
0.98
350
100
1.16
320
85
1.20
330
55
1.50
280
37
1.90
240
26
2.20
230
20
4.25
150
21
6.70
120
Color
code
Brown
Orange
Yellow
Brown
Green
Blue
Brown
Violet
Gray
Black
Brown
Red
Yellow
Green
1. When ordering, please specify termination and packaging codes:
0805AF-103XJRC
Termination: R = RoHS compliant matte tin over nickel over silver-
platinum-glass frit.
Special order:  Q = RoHS tin-silver-copper
(95.5/4/0.5) or P = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter C instead.
2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture
in Agilent/HP 4286A impedance analyzer with Coilcraft-provided
correlation pieces.
3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture.
4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft
SMD‑D test fixture.
5. DCR measured on Cambridge Technology Micro-ohmmeter.
6. Current that causes a 15°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute
maximum ratings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Designer’s Kit C450 contains 10 of each value
Core material Ferrite
Environmental  RoHS compliant without exemption, halogen free
Terminations  RoHS compliant matte tin over nickel over silver-
platinum-glass frit. Other terminations available at additional cost.
Weight  16.7 – 18.0 mg
Ambient temperature  –40°C to +85°C with Irms current
Maximum part temperature  +100°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +100°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging  2000/7″reel; Plastic tape:  8 mm wide, 0.23 mm thick,
4 mm pocket spacing, 1.65 mm pocket depth
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Document 781-1  Revised 10/12/15