0402HL Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Higher inductance values than other 0402 ceramic chip inductors

Document 913-1
Chip Inductors – 0402HL (1005)
• Higher inductance values than other 0402 ceramic chip
inductors
• 12 inductance values from 270 nH to 820 nH
^  Inductance^{2  } SRF typ^{3  } DCR max^{4  } Irms⁵
  _{Part number}1 _{±5% (nH) (MHz) (Ohms) (mA)}
0402HL-271XJR_ 270
0402HL-301XJR_ 300
0402HL-331XJR_ 330
0402HL-361XJR_ 360
0402HL-391XJR_ 390
590
1.95
190
600
2.15
190
513
2.23
170
485
2.36
170
260
2.35
170
0402HL-471XJR_ 470
0402HL-511XJR_ 510
0402HL-561XJR_ 560
0402HL-601XJR_ 600
0402HL-681XJR_ 680
220
2.67
160
450
3.50
150
420
3.70
140
440
3.78
130
380
5.15
120
0402HL-741XJR_ 740
0402HL-821XJR_ 820
165
5.45
110
385
5.85
90
1. When ordering, please specify termination and packaging codes:
0402HL-821XJRW
Termination: R = RoHS compliant matte tin over nickel over silver-
platinum-glass frit.
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
Packaging: W = 7″ machine-ready reel. EIA-481 punched paper
tape (2000 parts per full reel).
U = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter W instead.
2. Inductance measured at 25 MHz using a Coilcraft SMD-F test fixture
and Coilcraft-provided correlation pieces with an Agilent/HP 4286
impedance analyzer.
3. SRF measured using Agilent/HP 8753D network analyzer and Coilcraft
SMD­‑D test fixture.
4. DCR measured on Cambridge Technology micro-ohmmeter and a
Coilcraft CCF858 test fixture.
5. Current that causes a 15°C temperature rise from 25°C ambient.
Because of their open construction, these parts will not saturate.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Core material Ceramic
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant matte tin over nickel over silver-plati-
num-glass frit. Other terminations available at additional cost.
Weight  0.7 – 1.3 mg
Ambient temperature  –40°C to +125°C with Irms current, +125°C
to +140°C with derated current
Storage temperature  Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance (TCL)  +25 to +150 ppm/°C
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
One per billion hours / one billion hours, calculated per Telcordia SR-332
Packaging  2000 per 7″ reel.  Paper tape: 8 mm wide, 0.66 mm thick,
2 mm pocket spacing
PCB washing  Only pure water or alcohol recommended
A max B max C max D E F G H I
0.048 0.031 0.022 0.010 0.018 0.008 0.026 0.014 0.025 inches
1,22 0,79 0,56 0,25 0,46 0,20 0,66 0,36 0,64 mm
Document 913-1  Revised 10/04/11