CLE230W Datasheet, PDF (1/1 Pages) Clairex Technologies, Inc – High Power Aluminum Gallium Arsenide IREDs

CLE230W, CLE231W, CLE232W
High Power Aluminum Gallium Arsenide IREDs
® _{Clairex}
Technologies, Inc.
July, 2001
0.156 (3.96)
0.136 (3.45)
0.165 (4.19)
0.145 (3.68)
0.190 (4.83)
0.176 (4.47)
1.00 (25.4) min.
0.100 (2.54) dia.
0.215 (5.46)
0.205 (5.21)
ANODE
CATHODE
0.025 (0.64) max.
0.010 (0.25) max ^{0.019 (0.48)}
0.016 (0.41)
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS)
0.147 (3.73)
0.137 (3.48)
features
absolute maximum ratings (T_A = 25°C unless otherwise stated)
• wide emission angle
storage temperature ...................................................................... -55°C to +150°C
• TO-46 hermetically sealed package
• excellent heat dissipation
• high power output
description
operating temperature ................................................................... -55°C to +125°C
lead soldering temperature⁽¹⁾ ......................................................................... 240°C
maximum continuous current⁽²⁾..................................................................... 100mA
peak forward current (10µs pulse width, 100pps) .............................................. 10A
maximum power dissipation⁽³⁾...................................................................... 200mW
The CLE230W series are AlGaAs
reverse voltage .................................................................................................... 3V
infrared emitting diodes mounted in
flat window TO-46 hermetic
packages. The wide emission angle
provides even illumination over a
large area. The series are spectrally
and mechanically matched to the
notes:
1. 0.06” (1.5mm) from the header for 5 seconds maximum. Maximum
temperature can be 260°C if wave soldering.
2. Derate linearly 0.80mA/°C from 25°C free air temperature to T_A = +125°C.
3. Derate linearly 1.6mW/°C from 25°C free air temperature to T_A = +125°C.
CLT130W phototransistor series. For
additional information, call Clairex.
electrical characteristics (T_A = 25°C unless otherwise noted)
symbol parameter
min typ max units test conditions
Irradiance^(4,5)
CLE230W ^1.5
-
-
E_e
CLE231W _3.5
-
-
mW/cm² IF = 100mA
CLE232W _5.0
-
-
V_F
Forward voltage^(4,5)
-
-
2.0
V
I_F = 100mA
I_R
Reverse current
-
-
10
µA
V_R = 3.0V
λ_P
Peak emission wavelength
-
890
-
nm
I_F = 100mA
BW
Spectral bandwidth at half power points
-
80
-
nm
I_F = 100mA
Θ_HP
Emission angle at half power points
-
70
-
deg. I_F = 100mA
t_r
Output rise time
-
500
-
ns
I_F = 100mA
t_f
Output fall time
-
250
-
ns
I_F = 100mA
note: 4. E_e is a measure of irradiance (power/unit area) within a .25” (6.35mm) diameter area, centered on the
mechanical axis of the device and spaced .466” (11.8mm) from the lens side of the tab. This is
geometrically equivalent to a 30° cone.
5. Measurement taken at trailing edge of 100µs pulse with a duty cycle of 0.1%.
Clairex reserves the right to make changes at any time to improve design and to provide the best possible product.
Revised 12/01/04
Clairex Technologies, Inc.
Phone: [phone]
1301 East Plano Parkway
Fax: [phone]
Plano, Texas 75074-8524
www.clairex.com