7101L1CWZQE Datasheet, PDF (6/14 Pages) C&K Components – 7000 Series Miniature Toggle Switches

7000 Series
Miniature Toggle Switches
BUSHING
BUSHING
Y
Y9
.350" HIGH,
THREADED, KEYWAY
.350" HIGH,
UNTHREADED,
KEYWAY
NONE
NO BUSHING
No bushing choice required
with KXX, TXX actuators.
(exception: Specify CW if
splashproof bushing desired).
D .280" HIGH,
H
THREADED, KEYWAY
D8 .280" HIGH, UNTHREADED,
D9
FLAT ³
.280" HIGH, UNTHREADED,
KEYWAY
BUSHING FINISH
.296" HIGH, FLAT
THREADED, HIGH TORQUE ^1,2
H3
.315" HIGH, KEYWAY
THREADED, HIGH
TORQUE ^1,2
1/4-40 UNS-2A
D8
1/4-40 UNS-2A
D, D9
1/4-40 UNS-2A
1/4-40 UNS-2A
Y bushing standard with C,
W-W5, Z or Z3 terminations.
H4
8mm HIGH, KEYWAY, THREADED,
METRIC HIGH TORQUE ^1,2,3
D9 bushing standard with all terminations
except C, W-W5, Z or Z3. Add .070 (1,78) to
all actuators lengths with D, D8 & D9 bushings.
Y1
.378" HIGH, KEYWAY, THREADED,
HIGH TORQUE ^1,2,4
Y3
8.9mm HIGH, KEYWAY,
THREADED, METRIC
Subtract .020 (0,51) from all actuator
lengths for H3 bushing.
Y4
.378" HIGH, FLAT, THREADED,
HIGH TORQUE ^1,2,5
1/4-40 UNS-2A
1/4-40 UNS-2A
CW
THREADED, SPLASHPROOF ^1,2
For T & T1 actuators.
For actuators other than T & T1.
OPTION
CODE
BUSHING FINISH
NONE
2
NICKEL on all bushings
except ‘D8’ satin chrome.
BLACK
15/32-32 UNS-2A
1/4-40 UNS-2A
IP67 Degree of protection, totally protected against
dust, full-scale voltage protection, temporary immersion.
Internal actuator seal standard.
IP67 Degree of protection, totally protected
External bushing seal available separately from APM
against dust, full-scale voltage protection,
Hexseal, part # MFS-60064.
temporary immersion. Internal actuator seal
and external bushing seal washer standard.
1 _{Will withstand 12 in.-lbs. of torque with no distortion.}
2 _{CW. H, H3, H4, Y1 & Y4 bushings not available on single pole models}
with A4 terminations.
3 _{D8 & H4 bushings available only with L, L1, L2, M & S actuators.}
4 _{Y1 bushing available only with LXP, MP, PX & SP actuators.}
5 _{Y4 bushing not available with L4X actuators.}
NOTE: Two mounting nuts, locking ring and lockwasher supplied standard with
threaded bushings. Black hardware is supplied when either black bushings or
actuators are specified. Optional mounting nut and locking ring styles and finishes
available, see Section N.
1/4 INCH BUSHING
PANEL MOUNTING
METRIC BUSHING
15/32 INCH BUSHING
F
Without locking ring. With standard locking ring. With small locking ring. Without locking ring. With locking ring. Without locking ring. With standard locking ring.
F–8
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
www.ck-components.com