BD01 Datasheet, PDF (1/2 Pages) ITT Industries – Standard Profile DIP Switches

BD Series
Standard Profile DIP Switches
Features/Benefits
Typical Applications
• Traditional full profile DIP switch
• Address switch for industrial controls
• Extended actuator for easy actuation • Logic switching for computers and
H _{• Open bottom construction allows for}
peripherals
solder washing without the need
• Function controlling for
for tape seal
numerous applications
• RoHS compliant
Specifications
SWITCH FUNCTION: SPST - 1 thru 12 position available
(except 11 position).
CONTACT RATING:
Carry: 100 mA max. @ 50 V DC.
Switch: 100 mA max. @ 5 V DC or 25 mA max. @ 25 V DC.
MECHANICAL AND ELECTRICAL LIFE: 10,000 make-and-break
cycles at full load, each circuit.
CONTACT RESISTANCE: Below 50 milliohms typ. initial
@ 2-4 V DC 100mA.
INSULATION RESISTANCE: 10⁹ ohms min.
DIELECTRIC STRENGTH: 500 V RMS min. @ sea level between
adjacent terminals.
CAPACITANCE: 5pF max. between adjacent terminals.
STORAGE & OPERATING TEMPERATURE: -40°C to 85°C.
SHOCK: Withstands 20g 11 ms sawtooth waveform with no con-
tact opening greater than 10 microseconds.
VIBRATION: No contact opening greater than 10 microseconds and no
contact closure when exposed to vibration .06 in DA or 5g,
whichever is less, from 10 to 55 Hz, and 10g from 55 to 500 Hz.
SOLDERABILITY: Per MIL-STD-202F method 208D, or EIA RS-186E
method 9 (1 hour steam aging).
PACKAGING: Switches supplied in rigid dispensing tubes in full-tube
quantities only: this may effect order quantity. Number of switches
per tube varies with model. Switch position 1 denotes pin number
1. All switch actuators in ‘OFF’ position, standard.
Materials
CASE & COVER: Glass filled polyester (PBT),
flame retardant (UL 94V-0).
ACTUATOR: Glass filled nylon 6/6, flame retardant,
heat stabilized (UL 94V-0)
CONTACTS: Gold over nickel over phosphor bronze.
TERMINALS: Matte-tin over nickel over phosphor bronze.
Note: Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Vertical Full Profile DIP
BD08
DIM 'A'
O
N
.380
(9,65)
12345678
.072
(1,83)
ACTUATOR
TRAVEL
Ø.038 TYP.
(0,97)
.100 TYP.
(2,54)
.300
(7,62)
.060 TYP.
(1,52)
.160 TYP.
(4,06)
DIM 'B'
.080 TYP.
(2,03)
.026
(0,66)
.300
(7,62)
.035
(0,9)
TYP.
.090
(2,29)
.100 TYP.
(2,54)
.020 TYP.
(0,51)
.141 TYP.
(3,58)
.007
(0,18)
.300
(7,62)
PART NUMBER
BD01
BD02
BD03
BD04
BD05
BD06
BD07
BD08
BD09
BD10
BD12
Schematic
NO.POS.
DIM. ‘A’
1
.180 (4,57)
2
.280 (7,11)
3
.380 (9,65)
4
.480 (12,19)
5
.580 (14,73)
6
.680 (17,27)
7
.780 (19,81)
8
.880 (22,35)
9
.980 (24,89)
10
1.080 (27,43)
12
1.280 (32,51)
QUANTITY
PER TUBE
115
74
54
43
35
30
26
23
21
19
16
SPST
H–14
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
www.ck-components.com