8060 Datasheet, PDF (1/10 Pages) ITT Industries – Alternate Action and Momentary Pushbutton Switches

8060 Series
Alternate Action and Momentary Pushbutton Switches
A
Features/Benefits
• Long travel
Typical Applications
• Instrumentation
• Available with LED
• Computers and peripherals
• Long life contact design
• Epoxy terminial seal
compatabile with bottom
wash cleaning
• Telecommunications and
networking equipment
• RoHS compliant models
available
Models Available
Specifications
Materials
CONTACT RATING: Q contact material: 6 AMPS @ 120 V AC
or 28 V DC; 3 AMPS @ 250 V AC. See page A-59 for
additional ratings.
ELECTRICAL LIFE: 50,000 make-and-break cycles at full load.
CASE: Glass filled nylon 6/6 or diallyl phthalate (DAP),
flame retardant (UL 94V-0).
PLUNGER: S, S1, S2 Options: Glass filled nylon or glass filled
polyester (PBT) (UL 94V-0). L, L1 Options: Brass, nickel plated.
CONTACT RESISTANCE: Below 20 mΩ typ. initial @
2-4 V DC, 100 mA, for both silver and gold plated contacts.
INSULATION RESISTANCE: 109Ω min.
DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.
OPERATING TEMPERATURE: –30ºC to 65ºC
SOLDERABILITY: Per MIL-STD-202F method 208D, or
EIA RS-186E method 9 (1 hour steam aging).
CAP INSTALLATION FORCE: 10 lbs. maximum permissible.
CAP & FRAME: Nylon, black standard.
BUSHING: Brass or zinc, nickel plated.
HOUSING: Stainless steel.
SWITCH SUPPORT: Brass or steel, matte-tin plated.
END CONTACTS: Q contact material: Coin silver, silver plated.
See page A-59 for additional contact materials.
CENTER CONTACT & ALL TERMINALS: Q contact material: Copper
alloy, silver plated. See page A-59 for additional contact materials.
NOTE: Any models supplied with P, R, S, Q, B or G contact material are RoHS compliant. ^{TERMINAL SEAL: Epoxy. Refer to soldering and cleaning}
in Technical Data Chapter.
NOTE: Specifications and materials listed above are for switches with standard options. ^{HARDWARE: Nut & Locking Ring: Brass, nickel plated;}
For information on specific and custom switches, consult Customer Service Center.
Lockwasher: Steel, nickel plated.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown
and described on pages A-53 thru A-61. For additional options not shown in catalog, consult Customer Service Center. All
models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods.
Switch Function
8161 SPDT On-On
8168 SPDT On-Mom.
8261 DPDT On-On
Actuator or Plunger
S .710" high plunger
with .375" dia. cap
J80 Snap-in
J81 Snap-in with frame
J82 Snap-in with frame for LED
J86 Snap-in with frame & LED
L .740" high plunger with
.395" dia. cap
L1 .740" high plunger with
.590" dia. cap
S1 .615" high plunger with
.200" dia. cap
S2 .710" high plunger with
.310" dia. cap
Bushing
H .300" high, flat, hi torque
Contact Material
H9 .300" high, flat, hi torque
B Gold
NONE No bushing choice required P Gold, matte-tin
Y3 7.6mm, keyway
Q Silver
Terminations
A Right angle, PC thru-hole
AV2 Vertical right angle,
PC thru-hole
S Silver, matte-tin
G Gold over silver
R Gold over silver,
matte-tin
C PC Thru-hole
Z Solder lug
Seal
A3 Right angle, snap-in, PC thru-hole
E Epoxy
AV3 Vertical right angle, snap-in,
I Epoxy potted base
PC thru-hole
V3 .460" high, V-bracket
V4 .630" high, V-bracket
V6 .460" high, V-bracket
V21 .555" high, snap-in V-bracket
V31 .460" high, snap-in V-bracket
W .750" long, wire wrap
Z3 Quick connect
Cap Color
2 Black
1 White
3 Red
4 Orange
5 Yellow
9 Gray
Frame Color
2 Black
LED Color
3 Red
NONE Models without LED
A-52
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
www.ck-components.com