CS403 Datasheet, PDF (5/6 Pages) Cherry Semiconductor Corporation – 5V, 750mA Linear Regulator with RESET

Application Notes
the longer leads is negligible.
Step 2: With the input voltage at its maximum value,
increase the load current slowly from zero to full load
while observing the output for any oscillations. If no oscil-
lations are observed, the capacitor is large enough to
ensure a stable design under steady state conditions.
Step 3: Increase the ESR of the capacitor from zero using
the decade box and vary the load current until oscillations
appear. Record the values of load current and ESR that
cause the greatest oscillation. This represents the worst
case load conditions for the regulator at low temperature.
Step 4: Maintain the worst case load conditions set in step
3 and vary the input voltage until the oscillations increase.
This point represents the worst case input voltage condi-
tions.
Step 5: If the capacitor is adequate, repeat steps 3 and 4
with the next smaller valued capacitor. A smaller capaci-
tor will usually cost less and occupy less board space. If
the output oscillates within the range of expected operat-
ing conditions, repeat steps 3 and 4 with the next larger
standard capacitor value.
Step 6: Test the load transient response by switching in
various loads at several frequencies to simulate its real
working environment. Vary the ESR to reduce ringing.
Step 7: Remove the unit from the environmental chamber
and heat the IC with a heat gun. Vary the load current as
instructed in step 5 to test for any oscillations.
Once the minimum capacitor value with the maximum
ESR is found, a safety factor should be added to allow for
the tolerance of the capacitor and any variations in regula-
tor performance. Most good quality aluminum electrolytic
capacitors have a tolerance of ± 20% so the minimum
value found should be increased by at least 50% to allow
for this tolerance plus the variation which will occur at
low temperatures. The ESR of the capacitor should be less
than 50% of the maximum allowable ESR found in step 3
above.
Calculating Power Dissipation
in a Single Output Linear Regulator
The maximum power dissipation for a single output regu-
lator (Figure 1) is:
{ } ^PD(max) ^{= V}IN(max) ^{- V}OUT(min) ^IOUT(max) ^{+ V}IN(max)^IQ
(1)
where:
V_IN(max) is the maximum input voltage,
V_OUT(min) is the minimum output voltage,
I_OUT(max) is the maximum output current, for the applica-
tion, and
I_Q is the quiescent current the regulator consumes at
I_OUT(max).
sible value of R_QJA can be calculated:
R_QJA =
150¡C - T_A
P_D
(2)
The value of R_QJA can then be compared with those in
the package section of the data sheet. Those packages
with R_QJA's less than the calculated value in equation 2
will keep the die temperature below 150¡C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
I_IN
V_IN
Smart
Regulator
}Control
Features
I_Q
I_OUT
V_OUT
Figure 1: Single output regulator with key performance parameters
labeled.
Heat Sinks
A heat sink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed
to determine the value of R_QJA.
R_QJA = R_QJC + R_QCS + R_QSA
(3)
where
R_QJC = the junctionÐtoÐcase thermal resistance,
R_QCS = the caseÐtoÐheatsink thermal resistance, and
R_QSA = the heatsinkÐtoÐambient thermal resistance.
R_QJC appears in the package section of the data sheet. Like
R_QJA, it is a function of package type. R_QCS and R_QSA are
functions of the package type, heatsink and the interface
between them. These values appear in heat sink data
sheets of heat sink manufacturers.
Once the value of P_D(max) is known, the maximum permis-
5