FPL11PT Datasheet, PDF (1/2 Pages) Chenmko Enterprise Co. Ltd. – FAST RECOVERY SILICON RECTIFIER

CHENMKO ENTERPRISE CO.,LTD
SURFACE MOUNT GLASS PASSIVATED
FAST RECOVERY SILICON RECTIFIER
VOLTAGE RANGE 50 - 1000 Volts CURRENT 1.0 Ampere
FPL11PT
THRU
FPL17PT
FEATURE
*Sm al l S u r f ac e M o u n t i n g T y p e. (SMP)
* Low leakage current
* Fast recovery times for high efficiency
* Glass passivated junction
* High temperature soldering guaranteed :
260^oC/10 seconds at terminals
0.081 (2.05)
0.077 (1.95)
(3)
SMP
0.170 (4.31)
0.163 (4.15)
(1)
0.077 (1.95)
0.073 (1.85)
0.005 (0.15 Min.)
(2)
0.019 (0.50 Min.)
0.045 (1.16)
0.042 (1.07)
0.019 (0.50 Min.)
CIRCUIT
2
1
3
MAXIMUM RATINGES ( At TA = 25^oC unless otherwise noted )
RATINGS
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current TL = 110^oC
Peak Forward Surge Current 8.3 ms single half sine-wave
superimposed on rated load (JEDEC method)
Typical Junction Capacitance (Note 1)
Maximum Thermal Resistance
(Note 2)
(Note 3)
Operating and Storage Temperature Range
0.264 (6.70)
0.254 (6.46)
0.212 (5.38)
0.208 (5.29)
0.055 (1.40)
0.051 (1.30)
Dimensions in inches and (millimeters)
SMP
SYMBOL
VRRM
VRMS
VDC
IO
FPL11PT FPL12PT FPL13PT FPL14PT FPL15PT FPL16PT FPL17PT UNITS
50
100 200 400 600 800 1000 Volts
35
70
140 280 420 560 700 Volts
50
100
200
400
600
800 1000 Volts
1.0
Amps
IFSM
CJ
R JL
R JA
TJ, TSTG
30
15
30
75
-65 to +150
Amps
pF
o_{C / W}
o_{C / W}
o_C
ELECTRICAL CHARACTERISTICS ( At TA = 25^oC unless otherwise noted )
CHARACTERISTICS
Maximum Instantaneous Forward Voltage at 1.0 A DC
Maximum DC Reverse Current
at Rated DC Blocking Voltage at TA = 25^oC
Maximum Full Load Reverse Current Average,
Full Cycle at TA = 55^oC
Maximum Reverse Recovery Time (Note 4)
SYMBOL
VF
IR
trr
FPL11PT FPL12PT FPL13PT FPL14PT FPL15PT FPL16PT FPL17PT UNITS
1.3
Volts
5.0
uAmps
100
uAmps
150
250
500
nSec
NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts
2. Thermal Resistance Junction to terminal 6.0 mm² copper pads to each terminal
3. Thermal Resistance Junction to ambient 6.0 mm² copper pads to each terminal
4. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A
2004-7