|
ESMQ161VSN561MP25S Datasheet, PDF (2/7 Pages) United Chemi-Con, Inc. – Snap Mount | |||
|
◁ |
SMQ Series
Engineering Bulletin Mar 07
SMQ Specifications - Snap Mount
Item
Category Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Dissipation Factor ( Tan â¦)
Characteristics
Ø25 to Ø85ØC
160 to 450VDC
82 to 3,900â®F
Ø20% ( M ) at Ø20ØC, 120Hz
I ⤠3 CV (â®A ) after 5 minutes at Ø20ØC.
Where I = Max. leakage current (â®A ), C = Nominal capacitance (â®F ) and V = Rated voltage ( V )
At Ø20ØC, 120Hz
Rated Voltage ( V )
Tan ⦠( DF ) Max.
160 - 250
0.15
315 - 400
0.15
420, 450
0.20
Low Temperature
Characteristics
At 120Hz, impedance ( Z ) ratio between the Ø25ØC value and Ø20ØC value shall not exceed
the values given below.
Rated Voltage ( V )
Z (Ø25ØC ) / Z (Ø20ØC )
160 - 250
4
315 - 400
8
420, 450
8
Rated Ripple Current Multipliers
Frequency (Hz )
DC Rated Voltage
160 - 250V
315 - 450V
50Hz
0.81
0.77
120Hz
1.00
1.00
300Hz
1.17
1.16
1kHz
1.32
1.30
10kHz
1.45
1.41
50kHz
1.50
1.43
Endurance
(Load Life)
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to Ø20ØC after
subjecting them to DC voltage for 2,000 hours at Ø85ØC with the rated ripple current applied.
The sum of the DC voltage and peak AC voltage must not exceed the full rated voltage of
the capacitors.
Capacitance change: ⤠Ø20% of initial measured value
Tan ⦠( DF )
: ⤠200% of initial specified value
Leakage current : ⤠initial specified value
The following specifications shall be satisfied when the capacitors are restored to Ø20ØC after
exposing them for 1,000 hours at Ø85ØC without voltage applied. The rated voltage shall be
applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than
48 hours before the measurements.
Capacitance change: ⤠Ø15% of initial measured value
Tan ⦠( DF )
: ⤠150% of initial specified value
Leakage current : ⤠initial specified value
Diagram of Dimensions - Snap Mount
Snap Mount
Type VSN Ã22~Ã35
PET Sleeve
See
Pin
Detail
PC board pin-out
D×1
* Vent
L×¢2
10
2-2x
VS Pin Dimensions
W2
Unit: mm
W1
Edge
P of can
W
Standard design does not have a plastic end disk.
*Vent may be located either on the bottom or side of the can.
Type
P
W
W1
W2
VSN
4.0Ø0.5 1.5Ø0.2 1.0
1.0
2 / 7 United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel 847-696-2000 Fax 847-696-9278 www.chemi-con.com
|
▷ |