E37X401HPN Datasheet, PDF (2/7 Pages) United Chemi-Con, Inc. – Large Can

U37X Series
Engineering Bulletin Mar 2013
U37X Specifications - Screw Terminals
Item
Category Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Rated Ripple Current Multipliers
Characteristics
؁40 to ؀85؇C
350 to 500VDC
1,200 to 18,000␮F at ؀25؇C, 120Hz
ؓ20% ( M ) at ؀25؇C, 120Hz
I ؄ 0.02CV (␮A ) or 5mA, whichever is smaller, after 5 minutes at ؀25؇C.
Where I = Max. leakage current (␮A ), C = Nominal capacitance (␮F ) and V = Rated voltage ( V )
Ambient Temperature (؇C )
؀45؇C
2.82
؀65؇C
1.73
؀85؇C
1.00
Endurance
(Load Life)
Useful Life
Frequency (Hz )
DC Rated Voltage
50Hz
120Hz
300Hz
1kHz
3kHz
10kHz
350 -500V
0.80
1.00
1.20
1.30
1.40
1.41
To determine maximum ripple current at a specified temperature and frequency, use the appropriate
multiplier shown. However, do not use both the temperature and frequency multipliers together.
The following specifications shall be satisfied when the capacitors are restored to ؀25؇C after
subjecting them to DC voltage for 15,000 hours at ؀85؇C with the rated ripple current applied.
The sum of the DC voltage and peak AC voltage must not exceed the full rated voltage of
the capacitors.
Capacitance change: ≤ 20% from initial measurement
ESR change
: ≤ 200% of initial specified limit
Leakage current : ≤ initial specified limit
With specified standard voltage and ripple current applied, typical life as function of ambient
temperature is listed below.
؀85؇C
؀65؇C
؀45؇C
20,000 hours max.
71,600 hours max.
175,000 hours max.
Capacitance change: ≤ 30% from initial measurement
ESR change
: ≤ 300% of initial specified limit
Leakage current : ≤ initial specified limit
Shelf Life
Vibration Rating
Maximum Tightening Torque
The following specifications shall be satisfied when the capacitors are restored to ؀25؇C after
exposing them for 500 hours at ؀85؇C without voltage applied. The rated voltage shall be
applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than
48 hours before the measurements.
Capacitance change: ≤ 20% from initial measurement
ESR change
: ≤ 200% of initial specified limit
Leakage current : ≤ initial specified limit
10 -55Hz, 10g sinusoidal in three axes, 2 hours per axis.
Terminal Code
Thread Size
3 Threads Engaged
6 Threads Engaged
HP
HL
CD
10 - 32 NF- 2B
M5x0.8 - 6H
2.0 N_·m ( 18.0 in_·lb)
2.8 N_·m ( 25.0 in_·lb)
CP
CH
CA
CS
1_{/4 - 28 NF- 2B}
M6x1- 6H
4.0 N_·m ( 35.0 in_·lb)
6.2 N_·m ( 55.0 in_·lb)
Typical Inductance (nH)
at 1MHz
Case Diameter
Terminal Code
(mm )
HP
HL
CD
CP
CH
CA
CS
Ø50.8
—
—
NA
NA
NA
NA
NA
Ø63.5
—
—
—
—
—
—
—
Ø76.2
30
30
25
20
25
20
25
Ø89.0
30
30
25
20
25
20
25
Custom Designs
Custom CV values per case size and termination type may be available upon request.
Contact appropriate representative with specific requirements.
Product specifications are subject to change without notice.
Ask for UCC product bulletins and review specifications before purchase and/or use. Please use our products based on parameters specified in our bulletins.
2 / 7 United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel [phone] Fax [phone] www.chemi-con.com