|
PASE4R0E Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Radial Lead | |||
|
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
ËSuper low ESR, high ripple current capability
ËDownsized from PSC series (Ð8Ê·8L to Ð6.3Ê·8L)
ËEndurance is longer life than PSC series (5,000 hours at 105Ë)
ËESR after endurance is specified within the initial spec
ËRated voltage range : 2.5 to 6.3Vdc
ËRoHS Compliant
ËHalogen Free
PSE
Longer life
Downsized
PSC
ËSPECIFICATIONS
Items
Characteristics
Category
Temperature Range -55 to +105Ë
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
2.5 to 6.3Vdc
ʶ20% (M)
Rated voltage(V)Ê·1.15
I=0.2CV or 500ÂA, whichever is greater
Where, I : Max. leakage current (ÂA), C : Nominal capacitance (ÂF), V : Rated voltage (V)
(at 20Ë, 120Hz)
(at 105Ë)
(at 20Ë after 2 minutes)
0.10 max.
(at 20Ë, 120Hz)
Z(-25Ë)/Z(+20Ë)ʽ1.15
Z(-55Ë)/Z(+20Ë)ʽ1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20Ëafter the rated voltage is applied for 5,000 hours
at 105Ë.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
D.F. (tanÐ)
ʽThe initial specified value
ESR
ʽThe initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20Ëafter subjecting them to DC voltage at 60$,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
D.F. (tanÐ)
ʽThe initial specified value
ESR
ʽThe initial specified value
Leakage current
ʽThe initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105Ë for 30 seconds
through a protective resistor(R=1kÐ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
D.F. (tanÐ)
ʽThe initial specified value
ESR
ʽThe initial specified value
Leakage current
ʽThe initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105Ë)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105Ë.
ËDIMENSIONS [mm]
ËTerminal Code : E
F08 Coated Case
Size code
ÐD
Ðd
F
ÐD'
L'
F08
H06
6.3
8.0
0.6
2.5
3.5
ÐD+0.5max.
L+1.5max.
ËMARKING
EX) 2.5V820.F
E 6D6
820
2.5V
H06
L'
Coated Case
15min.
4min.
L'
15min.
4min.
Product speciï¬cations in this catalog are subject to change without notice.Request our product speciï¬cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speciï¬cations.
(1/2)
CAT. No. E1001L
|
▷ |