ETXH201VSN561MR30S Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS

LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Long life snap-ins, 105℃
TXHSeries
・Endurance with ripple current : 10,000 hours at 105℃
・Non solvent resistant type
・RoHS Compliant
TXH
Longer life
LXM P272
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Characteristics
-25 to +105℃
200 to 450Vdc
±20% (M)
(at 20℃, 120Hz)
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 5 minutes)
Rated voltage (Vdc)
200 to 400V
450V
tanδ (Max.)
0.15
0.20
(at 20℃, 120Hz)
Rated voltage (Vdc)
200 to 400V
450V
Z (-25℃)/Z (+20℃)
4
8
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 10,000 hours at 105℃.
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦±15% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
Leakage current
≦The initial specified value
◆DIMENSIONS [mm]
●Terminal Code : VS (φ30 toφ40) : Standard
Sleeve (PET : Brown)
Negative mark
PC board pin-out
(View from Solder side)
10
●Terminal Code : LI (φ35,φ40)
Sleeve (PET : Brown)
Negative mark
PC board pin-out
(View from Solder side)
2-1.2×6
Vent
L±2
*_4.0±0.5
2-φ2
*φD=40mm : 3.5±0.5mm
The standard design has no plastic disc.
Vent
L±2
*₄*_.5±1
**φD=40mm : 4.0±1
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E T XH
VS N
M
S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 470µF:471, 1,000µF:102)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 200V:201 , 450V:451)
Series code
Category
Please refer to "Product code guide (snap-in type)"
5±0.5
14.2±1
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
270
CAT. No. E1001Q