|
ESMR401VSN151MP25S Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS | |||
|
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Downsized snap-ins, 85â
SMRSeries
ã»Endurance with ripple current : 2,000 hours at 85â
ã»Downsized and high ripple current from SMQ series
ã»Non solvent resistant type
ã»RoHS Compliant
SMR
Downsized
Higher ripple
SMQ P233
âSPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Characteristics
-25 to +85â
400 to 450Vdc
±20% (M)
(at 20â, 120Hz)
Iâ¦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â after 5 minutes)
Rated voltage (Vdc)
400V
420 & 450V
tanδ (Max.)
0.15
0.20
(at 20â, 120Hz)
Rated voltage (Vdc)
400 to 450V
Z(-25â)/Z(+20â)
8
(at 120Hz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 85â.
Capacitance change
â¦Â±20% of the initial value
D. F. (tanδ)
â¦200% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after exposing them for 1,000 hours at 85â without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
â¦Â±15% of the initial value
D. F. (tanδ)
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
âDIMENSIONS [mm]
âTerminal Code : VS (Ï22 toÏ35) : Standard
Sleeve (PET : Black)
Negative mark
PC board pin-out
(View from Solder side)
10
âTerminal Code : LI (Ï35)
Sleeve (PET : Black)
Negative mark
PC board pin-out
(View from Solder side)
2-1.2Ã6
Vent
L±2.5
4.0±0.5
2-Ï2
Vent
The standard design has no plastic disc.
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E SMR AAA V S N AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 180µF:181, 1,000µF:102)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 400V:401, 450V:451)
Series code
Category
Please refer to "Product code guide (snap-in type)"
L±2.5
4.5±1
5±0.5
14.2±1
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
231
CAT. No. E1001Q
|
▷ |