EMZR6R3ADA681MF80G Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
Low ESR, 105℃
MZR AIchip^TM-
Series
・Downsizing and Lower ESR, 2,000hours at 105℃
・Rated voltage range : 6.3 to 50V, Nominal capacitance range : 100 to 2,200μF
・Solvent resistant type(see PRECAUTIONS AND GUIDELINES)
・Vibration resistance structure
・RoHS Compliant
・AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
MZR
Downsized
MZJ P98
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Surge Voltage Test
Characteristics
-55 to +105℃
6.3 to 50Vdc
±20% (M)
(at 20℃, 120Hz)
I=0.01CV or 3μA, whichever is greater.
Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V)
(at 20℃ after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
(at 20℃, 120Hz)
tanδ(Max.)
0.26 0.19 0.16 0.14 0.12 0.10
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
(at 120Hz)
Z(-25℃)/Z(+20℃)
222222
Z(-40℃)/Z(+20℃)
333333
Z(-55℃)/Z(+20℃)
444333
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Capacitance change
≦±30% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦±30% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30±5 seconds through
a protective resistor (as required for RC=0.1±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35℃.
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
Surge voltage (Vdc)
7.2V 12V 18V 29V 40V 58V
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does
not imply long-term use at all.
◆DIMENSIONS [mm]
● Terminal Code : A
● Size code : F80 to JA0
Vent for JA0
W
● Terminal Code : G(Vibration resistant structure)
● Size code : HA0 and JA0
Vent for JA0
0.3max.
W
Size code D L A B C
W
P
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
HA0
8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
JA0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
0.3max.
A±0.2
L±0.3 (Note)
Note : L±0.5 for HA0 and JA0
L±0.5
◆MARKING
EX) 35V330µF
● Rated voltage symbol
3Q
330
V^ZR
Rated voltage (Vdc) 6.3
10
16
Symbol
j
A
C
A±0.2
: Dummy terminals
25
35
50
E
V
H
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection
circuit should be used if applied voltage will exceed the rated voltages.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
96
CAT. No. E1001Q