EMZJ350ADA Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Low ESR, 105℃

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
Low ESR, 105℃
MZJ AIchip^TM-
Series
・Lower ESR, 2,000 hours at 105℃
・Rated voltage range : 6.3 to 35V
・Nominal capacitance range : 10 to 1,800μF
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・Vibration resistant structure
・RoHS Compliant
MZJ
Lower ESR
MZA P74
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105℃
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Surge Voltage Test
6.3 to 35Vdc
±20% (M)
(at 20℃, 120Hz)
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 2 minutes)
Rated voltage (Vdc)
6.3V 10V
16V
25V
35V
tanδ(Max.)
0.26 0.19 0.16 0.14 0.12
(at 20℃, 120Hz)
Rated voltage (Vdc)
6.3V 10V
16V
25V
35V
Z(-25℃)/Z(+20℃)
2
2
2
2
2
Z(-40℃)/Z(+20℃)
3
3
3
3
3
Z(-55℃)/Z(+20℃)
4
4
4
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Capacitance change ≦±30% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ≦±30% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30±5 seconds through
a protective resistor (as required for RC=0.1±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35℃.
Rated voltage (Vdc)
6.3V 10V
16V
25V
35V
Surge voltage (Vdc)
7.2V 12V
18V
29V
40V
Appearance
No significant damage
Capacitance change ≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does not
imply long-term use at all.
◆DIMENSIONS [mm]
● Terminal Code : A
● Size code : D61 to JA0
Vent for JA0
W
● Terminal Code : G(Vibration resistant structure)
● Size code : HA0 and JA0
Vent for JA0
0.3max.
W
Size code D L A B C
W
P
D61
4 5.8 4.3 4.3 5.1 0.5 to 0.8 1.0
E61
5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
HA0
8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
JA0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
0.3max.
A±0.2
L±0.3 (Note)
Note : L±0.5 for HA0 and JA0
L±0.5
◆MARKING
EX) 35V10µF
9j
10
V^ZJ
● Rated voltage symbol
Rated voltage (Vdc) 6.3
10
16
Symbol
j
A
C
A±0.2
: Dummy terminals
25
35
E
V
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection
circuit should be used if applied voltage will exceed the rated voltages.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
72
CAT. No. E1001N