EMVH500ARA101MKE0S Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – High heat resistance, 125C

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
High heat resistance, 125C
@Lower ESR, Higher ripple current
@Endurance : 1,000 to 5,000 hours at 125C
@Suitable to fit for automotive equipment
@Solvent resistant type (10 to 50V)
@RoHS Compliant
MVH
125C
MVE
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-40 to +125C}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
10 to 450Vdc
P20% (M)
(at 20C, 120Hz)
Rated voltage (Vdc)
10 to 100Vdc
160 to 450Vdc
F60 to JA0
KE0 to MN0
I=0.01CV or 3MA, whichever is greater.
I=0.04CV+100
I=0.03CV or 4MA, whichever is greater.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C after 2 minutes)
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80V 100V 160 to 250V 400 & 450V
tanE (Max.) ^{F60 to JA0}
0.24 0.20 0.16 0.14 0.14 0.12 0.12 0.10
-
-
KE0 to MN0
0.22 0.18 0.16 0.14 0.12 0.14 - 0.10
0.20
0.24
When nominal capacitance exceeds 1,000MF, add 0.02 to the value above for each 1,000MF increase.
(at 20C, 120Hz)
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80V 100V 160 to 250V 400 & 450V
F60 to JA0 ^{Z(-25C)/Z(+20C) 3}
2
2
2
2
2
2
2
-
-
Z(-40C)/Z(+20C) 6 4 4 3 3 3 3 3
-
-
Z(-25C)/Z(+20C) 4 3 2 2 2 2 - 2
3
6
KE0 to MN0
Z(-40C)/Z(+20C) 8 6 4 3 3 3 - 3
6
10
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for the specified
time at 125C.
F60 to H63 (10 to 100Vdc) : 1,000hours
Time
HA0 to JA0 (10 to 100Vdc) : 2,000hours
KE0 to MN0 (10 to 100Vdc) : 5,000hours
KE0 to MN0 (160 to 450Vdc) : 2,000hours
Capacitance change [P30% of the initial value
D.F. (tanE)
[300% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours (500 hours
for 400 to 450Vdc) at 125C without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage
according to Item 4.1 of JIS C 5101-4.
Rated voltage(Vdc)
10 to 50Vdc
63 to 450Vdc
Capacitance change [P30% of the initial value
[P30% of the initial value
D.F. (tanE)
[300% of the initial specified value [300% of the initial specified value
Leakage current
[The initial specified value
[500% of the initial specified value
?DIMENSIONS [mm]
@Terminal Code : A
@Size code : F60 to MN0
W
0.3max.
AP0.2
LP0.5 (Note)
Note : LP0.3 for F60 and F80
@Terminal Code : G
@Size code : LH0 to MN0
0.3max.
W
Size code D L A B C
W
P
F60 6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H63
8 6.3 8.3 8.3 9.0 0.5 to 0.8 2.3
HA0
8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
JA0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
KE0 12.5 13.5 13.0 13.0 13.7 1.0 to 1.3 4.2
KG5 12.5 16.0 13.0 13.0 13.7 1.0 to 1.3 4.2
LH0
16 16.5 17.0 17.0 18.0 1.0 to 1.3 6.5
LN0
16 21.5 17.0 17.0 18.0 1.0 to 1.3 6.5
MH0 18 16.5 19.0 19.0 20.0 1.0 to 1.3 6.5
MN0 18 21.5 19.0 19.0 20.0 1.0 to 1.3 6.5
?MARKING
F60 to JA0
EX) 35V47MF
74H
47
35V
KE0 to MN0
EX) 16V1,000MF
0V
MVH
1000
16V
LP0.5
AP0.2
: Dummy terminals
(1/2)
CAT. No. E1001K