EMVA4R0ADA330MD55G Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
Downsized, 85C
MVA
@F4 through F18 case sizes are fully lined up
@Endurance : 85C 2000 hours
@Suitable to fit for downsized equipment
@Solvent-proof type except 100 to 450Vdc (see PRECAUTIONS AND GUIDELINES)
@Pb-free design
downsized
size extended
MV
?SPECIFICATIONS
Items
Category
Temperature Range ^{-40 to +85C}
Characteristics
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
4 to 450Vdc
P20% (M)
(at 20C, 120Hz)
Rated voltage (Vdc)
4 to 100V
160 to 450V
D55 to JA0 I=0.01CV or 3MA, whichever is greater.(after 2 minutes)
-
KE0 to MN0 I=0.03CV or 4MA, whichever is greater.(after 1 minute)
I=0.04CV+100MA max.(after 1 minute)
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C)
Rated voltage (Vdc)
4V 6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 400 & 450V
tanE (Max.)
D55 to JA0 0.42 0.35 0.30 0.26 0.16 0.14 0.12 0.12 0.12 -
-
KE0 to MN0 - 0.38 0.34 0.30 0.26 0.22 0.18 0.14 0.10 0.20
0.25
When nominal capacitance exceeds 1000MF, add 0.02 to the value above for each 1000MF increase.
(at 20C, 120Hz)
Rated voltage (Vdc)
4V 6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 400 & 450V
D55 to JA0
Z(-25C)/Z(+20C) 7 4 3 2 2 2 2 2 3
-
-
Z(-40C)/Z(+20C) 17 10 8 6 4 3 3 3 4
-
-
KE0 to MN0
Z(-25C)/Z(+20C) - 5 4 3
Z(-40C)/Z(+20C) - 12 10 8
22
54
222
333
3
6
6
10 (at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours
at 85C.
Size code
D55 to JA0
D55 to JA0
KE0 to MN0
Rated voltage (Vdc)
4V & 6.3V
10 to 100V
6.3 to 450V
Capacitance change [P30% of the initial value
[P20% of the initial value
DF (tanE)
[200% of the initial specified value [200% of the initial specified value
Leakage current
[The initial specified value
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 85C
without voltage applied.
Size code
D55 to JA0
D55 to JA0
KE0 to MN0
Rated voltage
4V & 6.3V
10 to 100V
6.3 to 450V
Capacitance change [P30% of the initial value
[P20% of the initial value
DF (tanE)
[200% of the initial specified value [200% of the initial specified value
Leakage current
[The initial specified value
[The initial specified value
?DIMENSIONS [mm]
@Terminal Code : A
@Size code : D55 to KG5
W
0.3max.
LP0.3(Note)
AP0.2
Note : LP0.5 for HA0 to KG5
@Terminal Code : G
@Size code : LH0 to MN0
0.3max.
W
LP0.5
AP0.2
: Dummy terminals
Size code D L A B C
W
P
D55
4 5.2 4.3 4.3 5.1 0.5 to 0.8 1.0
E55
5 5.2 5.3 5.3 5.9 0.5 to 0.8 1.4
F55 6.3 5.2 6.6 6.6 7.2 0.5 to 0.8 1.9
F60 6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
HA0
8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
JA0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
KE0 12.5 13.5 13.0 13.0 13.7 1.0 to 1.3 4.2
KG5 12.5 16.0 13.0 13.0 13.7 1.0 to 1.3 4.2
LH0 16 16.5 17.0 17.0 18.0 1.0 to 1.3 6.5
LN0 16 21.5 17.0 17.0 18.0 1.0 to 1.3 6.5
MH0 18 16.5 19.0 19.0 20.0 1.0 to 1.3 6.5
MN0 18 21.5 19.0 19.0 20.0 1.0 to 1.3 6.5
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E MVA AAA A AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 0.1MF:R10,100MF:101)
Taping·Tray code
Terminal code (A, G)
Voltage code (ex. 6.3V:6R3,100V:101,450V:451)
Series code
Category
Please refer to "A guide to global code (surface mount type)"
?MARKING
D55 to JA0
EX) 16V47MF
7hA
47
16V
KE0 to HN0
EX) 25V1000MF
0V
MVA
1000
25V
(1/2)
CAT. No. E1001E