ELZA250E Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Low impedance, Downsized, 105℃

MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, Downsized, 105℃
LZA Upgrade!
Series
・Adoption of innovative electrolyte and new technologies
・Very low impedance at high frequency
・Endurance with ripple current: 4,000 to 7,000 hours at 105℃
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
LZA
Lower Z
Downsized
LXZ P158
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105℃
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 35Vdc
±20% (M)
(at 20℃, 120Hz)
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
tanδ (Max.)
0.22 0.19 0.16 0.14 0.12
When nominal capacitance exceeds 1,000µF, add 0.02 to the value above for each 1,000µF increase.
(at 20℃, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
Z(-55℃)/Z(+20℃)
4
3
3
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the specified period of time at 105℃.
Time
φ10 : 4,000hours　 φ12.5 : 5,000hours　 φ16 to φ18 : 7,000hours
Rated voltage
6.3 to 10Vdc(φ10)
6.3 to 10Vdc(φ12.5 to φ18)
16 to 35Vdc
Capacitance change ≦±30% of the initial value
≦±20% of the initial value
≦±20% of the initial value
D.F.(tanδ)
≦300% of the initial specified value ≦200% of the initial specified value ≦200% of the initial specified value
Leakage current
≦The initial specified value
≦The initial specified value
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
6.3 to 10Vdc(φ10)
6.3 to 10Vdc(φ12.5 to φ18)
16 to 35Vdc
Capacitance change ≦±30% of the initial value
≦±20% of the initial value
≦±20% of the initial value
D.F.(tanδ)
≦300% of the initial specified value ≦200% of the initial specified value ≦200% of the initial specified value
Leakage current
≦The initial specified value
≦The initial specified value
≦The initial specified value
◆DIMENSIONS [mm]
●Terminal Code : E
Sleeve (PET : Dark blue)
L'
Vent
15min.
4min.
(φ10)
(φ12.5 to φ18)
Gas escape end seal
φD 10
12.5
16
18
φd 0.6
0.6
0.8
0.8
F 5.0
5.0
7.5
7.5
φD'
φD+0.5max.
L'
L+1.5max.
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E L ZA AAA E AA AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 680µF:681, 2,200µF:222)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 25V:250)
Series code
Category
Please refer to "Product code guide (radial lead type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
156
CAT. No. E1001N