|
ELZA160E Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Low impedance, Downsized, 105℃ | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, Downsized, 105â
LZA Upgrade!
Series
ã»Adoption of innovative electrolyte and new technologies
ã»Very low impedance at high frequency
ã»Endurance with ripple current: 4,000 to 7,000 hours at 105â
ã»Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
ã»RoHS Compliant
LZA
Lower Z
Downsized
LXZ P158
âSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105â
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 35Vdc
±20% (M)
(at 20â, 120Hz)
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
tanδ (Max.)
0.22 0.19 0.16 0.14 0.12
When nominal capacitance exceeds 1,000µF, add 0.02 to the value above for each 1,000µF increase.
(at 20â, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
Z(-55â)/Z(+20â)
4
3
3
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20â after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the specified period of time at 105â.
Time
Ï10 : 4,000hoursã Ï12.5 : 5,000hoursã Ï16 to Ï18 : 7,000hours
Rated voltage
6.3 to 10Vdc(Ï10)
6.3 to 10Vdc(Ï12.5 to Ï18)
16 to 35Vdc
Capacitance change â¦Â±30% of the initial value
â¦Â±20% of the initial value
â¦Â±20% of the initial value
D.F.(tanδ)
â¦300% of the initial specified value â¦200% of the initial specified value â¦200% of the initial specified value
Leakage current
â¦The initial specified value
â¦The initial specified value
â¦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20â after exposing them for 1,000 hours at 105â without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
6.3 to 10Vdc(Ï10)
6.3 to 10Vdc(Ï12.5 to Ï18)
16 to 35Vdc
Capacitance change â¦Â±30% of the initial value
â¦Â±20% of the initial value
â¦Â±20% of the initial value
D.F.(tanδ)
â¦300% of the initial specified value â¦200% of the initial specified value â¦200% of the initial specified value
Leakage current
â¦The initial specified value
â¦The initial specified value
â¦The initial specified value
âDIMENSIONS [mm]
âTerminal Code : E
Sleeve (PET : Dark blue)
L'
Vent
15min.
4min.
(Ï10)
(Ï12.5 to Ï18)
Gas escape end seal
ÏD 10
12.5
16
18
Ïd 0.6
0.6
0.8
0.8
F 5.0
5.0
7.5
7.5
ÏD'
ÏD+0.5max.
L'
L+1.5max.
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E L ZA AAA E AA AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 680µF:681, 2,200µF:222)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 25V:250)
Series code
Category
Please refer to "Product code guide (radial lead type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
156
CAT. No. E1001N
|
▷ |