ELXH201VSN271MP25S Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS

LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Long life, Overvoltage-proof design, 105C
@No sparks against DC over-voltage
@Same case sizes of KMH
@Endurance with ripple current : 105C 5000 hours
@Non solvent-proof type
@Pb-free design
LXH
downsized
longer life
KLG
downsized
CHA
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-25 to +105C}
Rated Voltage
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
ESL
DC Overvoltage Test
Endurance
Shelf Life
200 & 400Vdc
P20% (M)
I=0.02CV or 3mA, whichever is smaller.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C, 120Hz)
(at 20C after 5 minutes)
0.15 max.
(at 20C, 120Hz)
Z(-25C) /Z(+20C)[4
(at 120Hz)
50nH max.
(at 20C, 1MHz)
When an excessive DC voltage is applied to the capacitors under the test conditions on next page, the vent shall operate and then the
capacitors shall become open-circuit without burning materials.
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for 3000 or 5000 hours at 105C.
Capacitance change [P20% of the initial value
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C
without voltage applied.
Capacitance change [P15% of the initial value
D.F. (tanE)
[150% of the initial specified value
Leakage current
[The initial specified value
?DIMENSIONS [mm]
@Terminal Code : VS (F22 to F35)
Sleeve (PET)
Negative mark
Vent
*
LP2
4.0P0.5
*FD=35mm : 3.5P0.5mm
No plastic disk is the standard design
PC board pin-out
10
2-F2
@105c Endurance with Rated Ripple Current
(%) ₊₂₀
200V1000MFF30B45L
400V330MFF30B45L
+10
0
-10
-20
-30
1
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E LXH AAA VS N AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 68MF:680,1500MF:152)
Dummy terminal code
Terminal code
Voltage code (ex. 200V:201,400V:401)
Series code
Category
Please refer to "A guide to global code (snap-in type)"
0.1
0.01
(MA) 1,000
100
?RATED RIPPLE CURRENT MULTIPLIERS
@Frequency Multipliers
Frequency (Hz) 50
120 300
1k
10k 50k
200Vdc
0.81 1.00 1.17 1.32 1.45 1.50
400Vdc
0.77 1.00 1.16 1.30 1.41 1.43
10
1
0
2,000
4,000
Time
6,000
8,000
(hours)
(1/2)
CAT. No. E1001E