|
ELXG630VSN Datasheet, PDF (1/3 Pages) United Chemi-Con, Inc. – Long life snap-ins, 105℃ | |||
|
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Long life snap-ins, 105â
LXGSeries
ã»Endurance with ripple current : 5,000 hours at 105â
ã»Non solvent resistant type
ã»RoHS Compliant
LXG
Longer life
KMQ P215
âSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-40 to +105â
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
10 to 100Vdc
(at 20â, 120Hz)
±20% (M)
I=0.02CV or 3mA, whichever is smaller.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â after 5 minutes)
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80 & 100V
tanδ (Max.)
0.60 0.45 0.30 0.25 0.20 0.15 0.15
(at 20â, 120Hz)
Capacitance change : Capacitance at the lowest operating temperature shall not be less than 70% of the 20â value.
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80 & 100V
Z(-25â)/Z(+20â)
4
4
3
3
2
2
2
Z(-40â)/Z(+20â)
15 15 10 8
6
6
5
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20â after subjected to DC voltage with rated ripple
current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours at 105â.
Capacitance change â¦Â±25% of the initial value
D.F. (tanδ)
â¦250% of the initial specified value
Leakage current
â¦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20â after exposing them for 500 hours at 105â without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial specified value
Leakage current
â¦The initial specified value
âDIMENSIONS [mm]
âTerminal Code : VS (Ï22 to Ï35) : Standard
Sleeve (PET : Brown)
Negative mark
PC board pin-out
10
âTerminal Code : LI (Ï35)
Sleeve (PET : Brown)
Negative mark
PC board pin-out
2-1.2Ã6
Vent
L±2
*4.0±0.5
*ÏD=35mm : 3.5±0.5mm
The standard design has no plastic disc.
2-Ï2
Vent
L±2
4.5±1
5±0.5
14.2±1
âPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E LXG AAA VS N AAA M AAA S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 390µF:391, 3,300µF:332)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 10V:100, 100V:101)
Series code
Category
Please refer to "Product code guide (snap-in type)"
âRATED RIPPLE CURRENT MULTIPLIERS
âFrequency Multipliers
Frequency (Hz) 50
120 300
1k
10k 50k
10 to 50Vdc
0.95 1.00 1.03 1.05 1.08 1.08
63 to 100Vdc 0.92 1.00 1.07 1.13 1.19 1.20
The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5â rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
252
CAT. No. E1001N
|
▷ |