ELXA401LGC Datasheet, PDF (1/4 Pages) United Chemi-Con, Inc. – long life screw terminals ,105℃

LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS long life screw terminals ,105℃
LXASeries
・Rated voltage range up to 525Vdc
・Endurance with ripple current : 5,000 hours at 105℃ (2,000 hours for 500Vdc & 525Vdc)
・High reliability products
・RoHS Compliant
LXA
Long life
KMH P270
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-40 to +105℃ (10 to 100Vdc) -25 to +105℃ (160 to 525Vdc)}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
Insulation Resistance
Insulation
Withstanding Voltage
Endurance
Shelf Life
10 to 525Vdc
-10 to +50% (T) (10 to 250Vdc) ±20% (M) (350 to 525Vdc)
I=0.02CV or 5mA, whichever is smaller.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃, 120Hz)
(at 20℃ after 5 minutes)
See STANDARD RATINGS (10 to 250Vdc) 0.20max (350 to 525Vdc)
(at 20℃, 120Hz)
Capacitance change C(-40℃)/C(+20℃)≧0.6(10 to 100Vdc) C(-25℃)/C(+20℃)≧0.7(160 to 250Vdc)
C(-25℃)/C(+20℃)≧0.65(350 to 525Vdc)
(at 120Hz)
When measured between the terminals that are connected to each other and to the mounting clamp on the insulating sleeve covering
the case by using an insulation resistance meter of 500Vdc, the insulation resistance shall not be less than 100MΩ.
When a voltage of 2,000Vac is applied for 1 minute between the terminals that are connected to each other and to the mounting clamp
on the insulating sleeve covering the case, there shall not be electrical damage.
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours (2,000 hours for 500 & 525Vdc products)
at 105℃.
Capacitance change ≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
10 to 250Vdc
350 to 525Vdc
Capacitance change ≦±15% of the initial value
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value ≦200% of the initial specified value
Leakage current
≦The initial specified value
≦The initial specified value
◆DIMENSIONS (Screw-Mount) [mm]
●Terminal Code : LG
Sleeve (Pb-free PVC : Brown)
●Mounting Clamp Code : B
A±1
W±1
●Mounting Clamp Code : C
360°
3
Vent
30°±5°
6
L+4max.
Plastic disk
G±1
φD
～φ63.5
φ76.2
φ89
G
10 to 250Vdc 350 to 525Vdc
6
6
5
6
5
4
φD
A BWH F
35
58 44 48 3.5 12.7
50
78 64 68 4.5 22.4
63.5
90 76 80 4.5 28.0
76.2 104.5 90 93.5 4.5 31.5
<Screw specifcations>
Plus hexagon-headed screw :M5×0.8×10
Maximum screw tightening torque :3.23Nm
* The screw and the mounting clamp are separately supplied and not attached to the product.
45°±5°
8
J
φD
EK J F
50
32.5 37.0 14.0 22.4
63.5 38.1 43.5 14.0 28.0
76.2 44.5 50.0 14.0 31.5
89
50.8 56.5 16.0 31.5
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E LXA AAA LG N AAA M AAA M
Supplement code
Size code
Capacitance tolerance code (ex. M, T)
Capacitance code (ex. 390µF:391, 3,300µF:332)
Mounting clamp code (N, B, C)
Terminal code
Voltage code (ex. 10V:100, 100V:101, 525V:5C1)
Series code
Category
Please refer to "Product code guide (screw-mount terminal type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
294
CAT. No. E1001N