ELLA500E Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Low leakage current, 85C

Engineering Bulletin No.575C / Jun.2010
Low leakage current, 85C
Aluminum Electrolytic Capacitors
@Endurance : 1,000 hours at 85C
@Low leakage current type
@Solvent resistant type
@RoHS Compliant
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-40 to +85C}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
Endurance
Shelf Life
Shelf Test
6.3 to 50Vdc
P20% (M)
(at 20C, 120Hz)
I=0.002CV or 0.2MA, whichever is greater.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C after 1 minute)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
tanE (Max.)
0.24 0.20 0.16 0.14 0.12 0.10
When nominal capacitance exceeds 1,000MF, add 0.02 to the value above for each 1,000MF increase.
(at 20C, 120Hz)
Leakage current
Leakage current at 85C : [10 times of the 20C specified value
Max. Impedance Ratio (at 120Hz)
Z(-25C)/Z(+20C)[4, Z(-40C)/Z(+20C)[8
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1,000 hours
at 85C.
Capacitance change [P20% of the initial value
D.F. (tanE)
[150% of the initial specified value
Leakage current
[The initial specified value
The same specifications as "Endurance" shall be satisfied when the capacitors are restored to 20C after exposing them for 500 hours
at 85C without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to
Item 4.1 of JIS C 5101-4.
The following specifications shall be satisfied when the capacitors are restored to 20C after leaving them for 6 months at a nominal
temperature (-10 to +40C) without voltage applied.
Capacitance change [P20% of the initial value
D.F. (tanE)
[150% of the initial specified value
Leakage current
[The initial specified value
?DIMENSIONS [mm]
@Terminal Code : E
Sleeve (PET : Black)
L'
Vent
(except F5)
15min.
4min.
(F5 to F10)
(F12.5 to F18)
Gas escape end seal
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E L LA AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 0.1MF:R10,100MF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
fD 5 6.3 8 10 12.5 16 18
fd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
fD'
FD+0.5max.
L'
L+1.5max.
Specifications in this bulletin are subject to change without notice.
NIPPON CHEMI-CON CORPORATION
1507
1