|
EKZM350ELL681MJ25S Datasheet, PDF (1/3 Pages) United Chemi-Con, Inc. – MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, 105Ë
,;. 4FSJFT
ËLong-Life version of KZH series
ËEndurance with ripple current : 6,000 to 10,000 hours at 105Ë
ËNewly innovative electrolyte is employed to minimize ESR
ËRated voltage range : 6.3 to 50Vdc, Nominal capacitance range : 27 to 10,000ÂF
ËNon solvent resistant type
ËRoHS Compliant
KZM
Longer life
KZH
Lower Z
KZE
ËSPECIFICATIONS
Items
Characteristics
Category
Temperature Range -40 to +105Ë
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
Endurance
Shelf Life
6.3 to 50Vdc
ʶ20% (M)
(at 20Ë, 120Hz)
I=0.01CV or 3ÂA, whichever is greater.
Where, I : Max. leakage current (ÂA), C : Nominal capacitance (ÂF), V : Rated voltage (V)
(at 20Ë after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
tanÐ (Max.)
0.22 0.19 0.16 0.14 0.12 0.10
When nominal capacitance exceeds 1,000ÂF, add 0.02 to the value above for each 1,000ÂF increase.
(at 20Ë, 120Hz)
Z(-25Ë)/Z(+20Ë) 2 max.
Z(-40Ë)/Z(+20Ë)
3 max.
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20Ë after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the specified period of time at 105Ë.
Time
Ð5 &Ð6.3 : 6,000hours Ð8 : 8,000hours Ð10 to Ð18 : 10,000hours
Capacitance change ʽʶ25% of the initial value (6.3, 10Vdc : ʽʶ 30%)
D.F. (tanÐ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20Ë after exposing them for 500 hours at 105Ë without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ʽʶ25% of the initial value (6.3, 10Vdc : ʽʶ30%)
D.F. (tanÐ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
ËDIMENSIONS [mm]
ËTerminal Code : E
Sleeve(PET : Brown)
L'
Vent
(ExceptÐ5 &Ð6.3)
15min.
4min.
(Ð5 to Ð10)
(Ð12.5 to Ð18)
Gas escape end seal
ÐD 5 6.3 8 10 12.5 16 18
Ðd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
ÐD'
ÐD+0.5max.
L'
L+1.5max.
ËPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KZM AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100ÂF:101, 1,000ÂF:102)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 10V:100)
Series code
Category
Please refer to "Product code guide (radial lead type)"
ËRATED RIPPLE CURRENT MULTIPLIERS
ËFrequency Multipliers
Frequency (Hz)
Capacitance (ÂF)
27 to 180
120
0.40
1k
0.75
10k
0.90
100k
1.00
220 to 560
0.50 0.85 0.94 1.00
680 to 1,800
0.60 0.87 0.95 1.00
2,200 to 3,900
0.75 0.90 0.95 1.00
4,700 to 10,000
0.85 0.95 0.98 1.00
Note : The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5Ë rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product speciï¬cations in this catalog are subject to change without notice.Request our product speciï¬cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speciï¬cations.
(1/3)
CAT. No. E1001M
|
▷ |