EKZM100ELL152MH20D Datasheet, PDF (1/4 Pages) United Chemi-Con, Inc. – Low impedance, 105C

MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, 105C
KZM
@Long-Life version of KZH series
@Endurance with ripple current : 6,000 to 10,000 hours at 105C
@Newly innovative electrolyte is employed to minimize ESR
@Rated voltage range : 6.3 to 50Vdc, Nominal capacitance range : 27 to 10,000MF
@Non solvent resistant type
@RoHS Compliant
Longer life
KZH
Lower Z
KZE
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-40 to +105C}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
Endurance
Shelf Life
6.3 to 50Vdc
P20% (M)
(at 20C, 120Hz)
I=0.01CV or 3MA, whichever is greater.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
tanE (Max.)
0.22 0.19 0.16 0.14 0.12 0.10
When nominal capacitance exceeds 1,000MF, add 0.02 to the value above for each 1,000MF increase.
(at 20C, 120Hz)
Z(-25C)/Z(+20C)
2 max.
Z(-40C)/Z(+20C)
3 max.
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for the specified period of time at 105C.
Time
F5 & F6.3 : 6,000hours F8 : 8,000hours F10 to F18 : 10,000hours
Capacitance change [P25% of the initial value (6.3, 10Vdc : [P30%)
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 500 hours at 105C without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change [P25% of the initial value (6.3, 10Vdc : [P30%)
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
?DIMENSIONS [mm]
@Terminal Code : E
Sleeve(PET : Brown)
L'
Vent
(Except F5 & F6.3)
15min.
4min.
(F5 to F10)
(F12.5 to F18)
Gas escape end seal
fD 5 6.3 8 10 12.5 16 18
fd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
fD'
FD+0.5max.
L'
L+1.5max.
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KZM AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100MF:101, 1,000MF:102)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 10V:100)
Series code
Category
Please refer to "Product code guide (radial lead type)"
?RATED RIPPLE CURRENT MULTIPLIERS
@Frequency Multipliers
Frequency (Hz)
Capacitance (mF)
27 to 180
120
0.40
1k
0.75
10k
0.90
100k
1.00
220 to 560
0.50 0.85 0.94 1.00
680 to 1,800
0.60 0.87 0.95 1.00
2,200 to 3,900
0.75 0.90 0.95 1.00
4,700 to 10,000
0.85 0.95 0.98 1.00
Note : The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5C rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
(1/3)
CAT. No. E1001K