|
EKZH160ETC221MF11D Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Low impedance, 105℃ | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, 105Ë
,;)4FSJFT
ËUltra Low impedance for Personal Computers Storage Equipment
ËEndurance with ripple current: 5,000 to 6,000 hours at 105Ë
ËNon solvent resistant type
ËRoHS Compliant
KZM
Longer life
KZH
Lower Z
KZE
ËSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-40 to +105Ë
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 35Vdc
ʶ20% (M)
(at 20Ë, 120Hz)
I=0.01CV or 3ÂA, whichever is greater.
Where, I : Max. leakage current (ÂA), C : Nominal capacitance (ÂF), V : Rated voltage (V)
(at 20Ë after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
tanÐ(Max.)
0.22 0.19 0.16 0.14 0.12
When nominal capacitance exceeds 1,000ÂF, add 0.02 to the value above for each 1,000ÂF increase.
(at 20Ë, 120Hz)
Z (-25Ë) / Z (+20Ë) 2max.
Z (-40Ë) / Z (+20Ë) 3max.
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20Ë after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage)for the specified period of time at 105Ë.
Time
Ð5 &Ð6.3 : 5,000hours Ð8 to Ð16 : 6,000hours
Capacitance change ʽʶ25% of the initial value (6.3, 10Vdc :ʽʶ30%)
D.F. (tanÐ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20Ë after exposing them for 500 hours at 105Ë without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ʽʶ25% of the initial value (6.3, 10Vdc :ʽʶ30%)
D.F. (tanÐ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
ËDIMENSIONS [mm]
ËTerminal Code : E
Sleeve (PET : Brown)
Vent
L'
(ExceptÐ5 &Ð6.3)
15min
4min
(Ð5 to Ð10)
(Ð12.5 to Ð18)
Gas escape end seal
ÐD 5
Ðd 0.5
F 2.0
ÐD'
L'
6.3 8 10 12.5 16
0.5 0.6 0.6 0.6 0.8
2.5 3.5 5.0 5.0 7.5
ÐD+0.5max.
L+1.5max.
ËPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KZH AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47ÂF:470, 100ÂF:101, 1,000ÂF:102)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3, 35V:350)
Series code
Category
Please refer to "Product code guide (radial lead type)"
Product speciï¬cations in this catalog are subject to change without notice.Request our product speciï¬cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speciï¬cations.
(1/2)
CAT. No. E1001M
|
▷ |