EKZG6R3ESS821MHB5D Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Aluminum Electrolytic Capacitors

Engineering Bulletin Tentative
No.705F / Nov.2004
Aluminum Electrolytic Capacitors
For your computer MOTHERBOARDS
Aluminum Electrolytic Capacitors
@Super low ESR/impedance capacitors due to very low resistivity electrolyte
@Rated voltage range : 6.3 to 16V, Nominal capacitance range : 470 to 3,300MF
@Assured lifetime: 2,000 hours at 105C with the rated ripple current applied
@The KZG series capacitors are designed for computer motherboards
@Non solvent-proof
Feature!
For PC Motherboards
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-40 to +105C}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 16Vdc
P20% (M)
(at 20C, 120Hz)
I=0.01CV or 3MA, whichever is greater.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc)
(at 20C after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V
tanE (Max.)
0.22 0.19 0.16
When nominal capacitance exceeds 1,000MF, add 0.02 to the value above for each 1,000MF increase.
(at 20C, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V
Z (-25C) / Z (+20C)
2
2
2
Z (-40C) / Z (+20C)
3
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current for 2,000 hours at 105C.
The sum of the DC voltage and peak AC voltage must not exceed the full rated voltage of the capacitors.
Capacitance change [P25% of the initial measured value
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours at 105C
without voltage applied. The rated voltage shall be applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not
more than 48 hours before the measurements.
Capacitance change [P25% of the initial measured value
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
?DIMENSIONS [mm]
@Terminal Code : E
Sleeve(Brown : PET)
Vent
L'
15min
4min
(F8 to F10)
Gas escape end seal
fD
8
10
fd
0.6
0.6
F
3.5
5.0
fD'
FD+0.5max.
L'
L+1.5max.
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KZG AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 470MF:471, 2,200MF:222)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100,16V:160)
Series code
Category
Specifications in this bulletin are subject to change without notice.
NIPPON CHEMI-CON CORPORATION
1241
1