|
EKY-6R3ELL472MK30S Datasheet, PDF (1/3 Pages) United Chemi-Con, Inc. – Low impedance, 105℃ | |||
|
MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Low impedance, 105Ë
,:4FSJFT
ËNewly innovative electrolyte is employed to minimize ESR
ËEndurance with ripple current : 4,000 to 10,000 hours at 105Ë
ËNon solvent resistant type
ËRoHS Compliant
KZH
Lower Z
KZE
Lower Z
KY
ËSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-40 to +105Ë
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 100Vdc
ʶ20% (M)
(at 20Ë, 120Hz)
I=0.01CV or 3ÂA, whichever is greater.
Where, I : Max. leakage current (ÂA), C : Nominal capacitance (ÂF), V : Rated voltage (V)
(at 20Ë after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
t a nÐ (Max.)
0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.09 0.08
When nominal capacitance exceeds 1,000ÂF, add 0.02 to the value above for each 1,000ÂF increase.
(at 20Ë, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
Z(-25Ë)/Z(+20Ë)
4
3
2
2
2
2
2
2
2
Z(-40Ë)/Z(+20Ë)
8
6
4
3
3
3
3
3
3
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20Ë after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for the specified period of time at 105Ë.
Time
6.3 to 10Vdc Ð5 & 6.3 : 4,000hours Ð8 & 10 : 6,000hours Ð12.5 to 18 : 8,000hours
16 to 100Vdc Ð5 & 6.3 : 5,000hours Ð8 & 10 : 7,000hours Ð12.5 to 18 : 10,000hours
Capacitance change ʽʶ25% of the initial value
D.F. (tanÐ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20Ë after exposing them for 500 hours at 105Ë without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ʽʶ25% of the initial value
D.F. (tanÐ)
ʽ200% of the initial specified value
Leakage current
ʽThe initial specified value
ËDIMENSIONS [mm]
ËTerminal Code : E
Sleeve (PET : Brown)
Vent
L'
(ExceptÐ5 &Ð6.3)
15min.
4min.
(Ð5 to Ð10)
(Ð12.5 to Ð18)
Gas escape end seal
ËPART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KY-
E
M
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 1.0ÂF:1R0,10ÂF:100,100ÂF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,50V:500)
Series code
Category
Please refer to "Product code guide (radial lead type)"
ÐD 5 6.3 8 10 12.5 16 18
Ðd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
ÐD'
ÐD+0.5max.
L'
L+1.5max.
Product speciï¬cations in this catalog are subject to change without notice.Request our product speciï¬cations before purchase and/or use. Please use our products based on the information contained in this catalog and product speciï¬cations.
(1/3)
CAT. No. E1001M
|
▷ |