EKMR3B1 Datasheet, PDF (1/3 Pages) United Chemi-Con, Inc. – Downsized snap-ins, 105℃

LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Downsized snap-ins, 105℃
KMRSeries
・Downsized 5mm in height from current snap-ins KMQ series
・Max. 50% up ripple current than same case size of KMQ series
・Endurance with ripple current : 2,000 hours at 105℃
・Rated voltage range : 160 to 450Vdc, Capacitance range : 100 to 3,300µF
・For inverter control, switching power supplies
・Non solvent resistant type
・RoHS Compliant
KMR
Downsized
KMQ P215
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-25 to +105℃}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
160 to 450Vdc
±20% (M)
(at 20℃, 120Hz)
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 5 minutes)
Rated voltage (Vdc)
160 to 250V 315 to 400V 420 & 450V
tanδ(Max.)
0.15
0.15
0.20
(at 20℃, 120Hz)
Rated voltage (Vdc)
160 to 250V 315 to 400V 420 & 450V
Z(-25℃)/Z(+20℃)
4
8
8
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 105℃.
Capacitance change ≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ≦±15% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
Leakage current
≦The initial specified value
◆DIMENSIONS [mm]
●Terminal Code : VS (φ22 toφ35) : Standard
Sleeve (PET : Brown)
Negative mark
PC board pin-out
10
●Terminal Code : LI (φ35)
Sleeve (PET : Brown)
Negative mark
PC board pin-out
2-1.2×6
2-φ2
Vent
L±2.5
4.0±0.5
Vent
The standard design has no plastic disc.
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KMR
VS N
M
S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 100µF:101, 2,700µF:272)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 160V:161, 315V:3B1, 450V:451)
Series code
Category
Please refer to "Product code guide (snap-in type)"
L±2.5
4.5±1
5±0.5
14.2±1
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
212
CAT. No. E1001N