EKMG6R3ESS330ME11D Datasheet, PDF (1/3 Pages) United Chemi-Con, Inc. – MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS

MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Standard, Downsized, 105C
@Downsized from KME series
@Solvent-proof type except 350 to 450Vdc
(see PRECAUTIONS AND GUIDELINES)
@Pb-free design
KMQ
downsized
KMG
downsized
KME
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-55 to +105C(6.3 to 100Vdc) -40 to +105C(160 to 400Vdc) -25 to +105C(450Vdc)}
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
6.3 to 450Vdc
P20% (M)
(at 20C, 120Hz)
6.3 to 100Vdc
160 to 450Vdc
I=0.03CV or 4MA, whichever is greater.
CV ^{Time After 1minute}
CV[1000 I=0.1CV+40 max.
After 5minutes
I=0.03CV+15 max.
CV>1000 I=0.04CV+100 max.
I=0.02CV+25 max.
(at 20C after 1 minute)
(at 20C)
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V 450V
tanE (Max.)
0.34 0.24 0.20 0.16 0.14 0.12 0.10 0.08 0.20
0.24 0.24
When nominal capacitance exceeds 1000MF, add 0.02 to the value above for each 1000MF increase.
(at 20C, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V 450V
Z(-25C)/Z(+20C)
54322222
3
6
6
Z(-40C)/Z(+20C)
12 10 8 5 4 3 3 3
4
6
-
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated
ripple current is applied for 1000 hours (2000 hours to meet the following two conditions 1) : 160Vdc and larger, 2) : F12.5 and larger) at 105C.
Capacitance change [P20% of the initial value
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C
without voltage applied.
Rated voltage
6.3 to 100Vdc
160 to 450Vdc
Capacitance change [P20% of the initial value
[P20% of the initial value
D.F. (tanE)
[200% of the initial specified value [200% of the initial specified value
Leakage current
[The initial specified value
[500% of the initial specified value
?DIMENSIONS [mm]
@Terminal Code : E
Sleeve (PET)
L'
Vent
(except F5)
15min.
4min.
(F5 to F10)
(F12.5 to F18)
Gas escape end seal
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KMG AAA E AA AAA M AAA N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 0.1MF:R10,10MF:100,100MF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,35V:350,100V:101)
Series code
Category
Please refer to "A guide to global code (radial lead type)"
fD 5 6.3 8 10 12.5 16 18
fd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F 2.0 2.5 3.5 5.0 5.0 7.5 7.5
fD'
FD+0.5max.
L'
L+1.5max
(1/3)
CAT. No. E1001E