EKLM201 Datasheet, PDF (1/1 Pages) United Chemi-Con, Inc. – 15mm height snap-ins, 105℃

LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS 15mm height snap-ins, 105℃
KLMSeries
・15mm height snap-ins
・Endurance with ripple current : 2,000 hours at 105℃
・Non solvent resistant type
・RoHS Compliant
KLM
Low profile
KMQ P215
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-25 to +105℃
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
160 to 400Vdc
±20% (M)
(at 20℃, 120Hz)
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20℃ after 5 minutes)
Rated voltage (Vdc)
160 to 400V
tanδ (Max.)
0.20
(at 20℃, 120Hz)
Rated voltage (Vdc)
160 to 400V
Z (-25℃)/Z (+20℃)
4
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 105℃.
Capacitance change ≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change ≦±15% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
Leakage current
≦The initial specified value
◆DIMENSIONS [mm]
●Terminal Code : VS
Sleeve (PET : Brown)
Negative mark
PC board pin-out
10
Vent
L±2
4.0±0.5
The standard design has no plastic disc.
2-φ2
◆STANDARD RATINGS
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
E KLM
VS N
M
S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47µF:470, 100µF:101)
Dummy terminal code
Terminal code
Voltage code (ex. 160V:161,400V:401)
Series code
Category
Please refer to "Product code guide (snap-in type)"
WV
(Vdc)
160
180
200
Rated ripple
Cap
(µF)
Case size
φD×L(mm)
tanδ
current
(Arms/
105℃,120Hz)
Part No.
150
22×15 0.20 0.68
180 25.4×15 0.20 0.79
220 25.4×15 0.20 0.88
270
30×15 0.20 0.96
330
30×15 0.20 1.06
390
35×15 0.20 1.20
120
22×15 0.20 0.61
150 25.4×15 0.20 0.73
180 25.4×15 0.20 0.79
220
30×15 0.20 0.86
270
30×15 0.20 0.96
330
35×15 0.20 1.10
390
35×15 0.20 1.17
120
22×15 0.20 0.61
150 25.4×15 0.20 0.73
180
30×15 0.20 0.79
EKLM161VSN151MP15S
EKLM161VSN181MQ15S
EKLM161VSN221MQ15S
EKLM161VSN271MR15S
EKLM161VSN331MR15S
EKLM161VSN391MA15S
EKLM181VSN121MP15S
EKLM181VSN151MQ15S
EKLM181VSN181MQ15S
EKLM181VSN221MR15S
EKLM181VSN271MR15S
EKLM181VSN331MA15S
EKLM181VSN391MA15S
EKLM201VSN121MP15S
EKLM201VSN151MQ15S
EKLM201VSN181MR15S
Rated ripple
WV
(Vdc)
Cap
(µF)
Case size
φD×L(mm)
tanδ
current
(Arms/
105℃,120Hz)
Part No.
220
30×15 0.20 0.90
200 270
35×15 0.20 1.00
330
35×15 0.20 1.07
82
22×15 0.20 0.50
100 25.4×15 0.20 0.59
250
120
150
25.4×15
30×15
0.20
0.20
0.65
0.71
180
30×15 0.20 0.79
220
35×15 0.20 0.90
39
22×15 0.20 0.35
47 25.4×15 0.20 0.40
56 25.4×15 0.20 0.44
400 68
30×15 0.20 0.46
82
30×15 0.20 0.51
100
35×15 0.20 0.56
120
35×15 0.20 0.62
EKLM201VSN221MR15S
EKLM201VSN271MA15S
EKLM201VSN331MA15S
EKLM251VSN820MP15S
EKLM251VSN101MQ15S
EKLM251VSN121MQ15S
EKLM251VSN151MR15S
EKLM251VSN181MR15S
EKLM251VSN221MA15S
EKLM401VSN390MP15S
EKLM401VSN470MQ15S
EKLM401VSN560MQ15S
EKLM401VSN680MR15S
EKLM401VSN820MR15S
EKLM401VSN101MA15S
EKLM401VSN121MA15S
◆RATED RIPPLE CURRENT MULTIPLIERS
●Frequency Multipliers
Frequency (Hz) 50
120 300
1k
10k 50k
160 to 250Vdc 0.81 1.00 1.17 1.32 1.45 1.50
400Vdc
0.77 1.00 1.16 1.30 1.41 1.43
The endurance of capacitors is reduced with internal heating produced
by ripple current at the rate of halving the lifetime with every 5℃ rise.
When long life performance is required in actual use, the rms ripple
current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
240
CAT. No. E1001N