APXH2R5ARA221MF60G Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
@Super low ESR, impedance and high heat resistance have been obtained by using con-
ductive polymer as electrolyte.
@Suitable for DC-DC converters, voltage regulators and decoupling applications.
@Endurance with ripple current : 125C 1000 hours
@Rated voltage range : 2.5 to 20Vdc, Capacitance range : 22 to 1000MF
@Case size range : F6.3B5.7L to F10B7.7L
@Pb-free design
?SPECIFICATIONS
Items
Category
Temperature Range ^{-55 to +125C}
Characteristics
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
2.5 to 20Vdc
P20% (M)
Rated voltageB1.15V
Shall not exceed value shown in STANDARD RATINGS.
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
0.12 max.
(at 20C, 120Hz)
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours
at 125C.
Appearance
No significant damage
Capacitance change [P20% of the initial value
DF (tanE)
[200% of the initial specified value
ESR
[200% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 1000 hours.
Appearance
No significant damage
Capacitance change [P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change [P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
1% per 1000 hours maximum (Confidence level 60%)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 125C.
?DIMENSIONS [mm]
@Terminal Code : A
W
0.3max.
LP0.3
AP0.2
Size code fD L A B C
W
P
F60 6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H70
8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
J80
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
?MARKING
EX) PXH20VC22MF60
H39F
22
20^V
?PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXH AAA A RA AAA M AAA G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10MF:100,100MF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "A guide to global code (conductive polymer type)"
(1/2)
CAT. No. E1001E