English
Language : 

APXG160ARA102 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
PXG NPCAPTM-
Series
・Super low ESR, high ripple current capability
・Rated voltage range : 16 to 25Vdc, Capacitance range : 10 to 1,000µF
・Case size : φ5×4.5L toφ10×12.2L
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
PXG
Downsized
PXE P40
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
-55 to +105℃
16 to 25Vdc
±20% (M)
Rated voltage×1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
(E46,F45 : 3,000 hours) at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours (E46,F45 : 500 hours).
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ)and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
●Terminal Code : A
W
0.3max.
L±0.3 (Note)
A±0.2
Note : L+0.1/-0.2 for E46 and F45
L±0.5 for HA0, JA0 and JC0
Size Code φD L A B C
W
P
E46
5 4.5 5.3 5.3 5.9 0.5 to 0.8 1.4
E61
5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
F45 6.3 4.4 6.6 6.6 7.2 0.5 to 0.8 1.9
F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
F80 6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H70
8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
H80
8 7.7 8.3 8.3 9.0 0.7 to 1.1 3.1
HA0
8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
J80
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
JA0 10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
JC0 10 12.2 10.3 10.3 11.0 0.7 to 1.1 4.5
◆MARKING
EX) 25V47µF
G14A
47
25V
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXG
A RA
M
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47µF:470, 100µF:101)
Taping code
Terminal code
Voltage code (ex. 16V:160, 20V:200)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
32
CAT. No. E1001Q
 ▷