APXE160ARA Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Surface Mount

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
˔Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
˔Rated voltage range : 2.5 to 16Vdc, Capacitance range : 33 to 2,700ŸF
˔Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
˔RoHS Compliant
˔Halogen Free
PXF
Lower ESR
PXE
Lower ESR
PXA
˗SPECIFICATIONS
Items
Characteristics
Category
Temperature Range ^{-55 to +105ˆ}
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
2.5 to 16Vdc
ʶ20% (M)
Rated voltageÊ·1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20ˆ, 120Hz)
(at 105ˆ)
(at 20ˆ after 2 minutes)
0.12 max.
(at 20ˆ, 120Hz)
Z(-25ˆ)/Z(+20ˆ)ʽ1.15
Z(-55ˆ)/Z(+20ˆ)ʽ1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after the rated voltage is applied for 2,000 hours
at 105ˆ.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
DF (tanЎ)
ʽ150% of the initial specified value
ESR
ʽ150% of the initial specified value
Leakage current
ʽThe initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20ˆ after subjecting them to the DC rated voltage at
60ˆ, 90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
DF (tanЎ)
ʽ150% of the initial specified value
ESR
ʽ150% of the initial specified value
Leakage current
ʽThe initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105ˆ for 30 seconds
through a protective resistor(R=1kЊ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change ʽʶ20% of the initial value
DF (tanЎ)
ʽ150% of the initial specified value
ESR
ʽ150% of the initial specified value
Leakage current
ʽThe initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105ˆ)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105ˆ.
˗DIMENSIONS [mm]
˔Terminal Code : A
W
0.3max.
Lʶ0.3 (Note)
Aʶ0.2
(Note) Lʶ0.5 for HA0, HC0, JA0, JC0
Size Code ПD L A B C
W
P
E61
5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
F61
6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
F80
6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H70
8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
H80
8 7.7 8.3 8.3 9.0 0.7 to 1.1 3.1
HA0
8 10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
HC0
8 12.0 8.3 8.3 9.0 0.7 to 1.1 3.1
J80
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
JA0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
JC0
10 12.2 10.3 10.3 11.0 0.7 to 1.1 4.5
˗MARKING
EX) 2.5V390ŸF
E49A
390
2.5^V
˗PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXE
A RA
M
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47μF:470,100μF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category _{Please refer to "Product code guide (conductive polymer type)"}
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001L