English
Language : 

APXA4R0ARA681 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
PXA NPCAPTM-
Series
・Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
・Rated voltage range : 2.5 to 25Vdc, case size range : φ4×5.2L toφ10×12.2L
・Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
◆SPECIFICATIONS
PXE P40
Lower ESR
PXA
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
-55 to +105℃
2.5 to 25Vdc
±20% (M)
Rated voltage×1.15 (Rated voltage 2.5 to 20Vdc, 25Vdc) / Rated voltage×1.00 (Rated voltage 23Vdc)
Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
(F45 : 3,000 hours) at 105℃.
Appearance
No significant damage
Bias Humidity
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours(F45 : 500 hours).
Appearance
No significant damage
Surge Voltage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Failure Rate
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
◆MARKING
●Terminal Code : A
W
0.3max.
A±0.2
L±0.3 (Note)
Note : L+0.1/-0.2 for F45
L±0.5 for HC0 and JC0
Size code φD L A B C
W
P
D55
4 5.2 4.3 4.3 5.1 0.5 to 0.8 1.0
E60
5 5.7 5.3 5.3 5.9 0.5 to 0.8 1.4
F45 6.3 4.4 6.6 6.6 7.2 0.5 to 0.8 1.9
F55 6.3 5.2 6.6 6.6 7.2 0.5 to 0.8 1.9
F60 6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H70
8 6.7 8.3 8.3 9.0 0.7 to 1.1 3.1
HC0
8 12.0 8.3 8.3 9.0 0.7 to 1.1 3.1
J80
10 7.7 10.3 10.3 11.0 0.7 to 1.1 4.5
JC0
10 12.2 10.3 10.3 11.0 0.7 to 1.1 4.5
EX) 16V39µF
A15L
39
16V
◆PART NUMBERING SYSTEM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A PXA
A RA
M
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10µF:100,100µF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
42
CAT. No. E1001Q