|
APSG160ELL471 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS | |||
|
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
PSG NPCAPTM-
Upgrade!
Series
ã»Super low ESR, high ripple current capability
ã»Added 35V
ã»Endurance: 15,000 to 20,000 hours at 105â
ã»Rated voltage : 16 to 35Vdc
ã»RoHS Compliant
ã»Halogen Free
PSG
Downsized
PSF P54
âSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
-55 to +105â
16 to 35Vdc
±20% (M)
Rated voltage(V)Ã1.15
I=0.2CV or 500µA, whichever is greater
Where, I : Leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20â, 120Hz)
(at 105â)
(at 20â after 2 minutes)
0.12 max.
(at 20â, 120Hz)
Z(-25â)/Z(+20â)â¦1.15
Z(-55â)/Z(+20â)â¦1.25
(at 100kHz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after the rated voltage is applied for 20,000 hours
(20 to 35V : 15,000 hours) at 105â.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjecting them to DC voltage at 60â,
90 to 95% RH for 1,000 hours.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦The initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage speciï¬ed at 105â for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦The initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
0.5% per 1,000 hours maximum (Conï¬dence level 60% at 105â)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105â.
âDIMENSIONS [mm]
âTerminal Code : E
F05,F08,H06,H08
Coated Case
L'
15min.
HB5,H16,H20,JB5,J16,J20
Coated Case
4min.
Size code F05 F08 H06 H08 HB5 H16 H20 JB5 J16 J20
ÏD
6.3
8.0
10.0
Ïd
0.45
0.6
F
2.5
3.5
5.0
ÏD'
ÏD+0.5max.
L'
L+1.0max. (Note1)
L+1.5max.
Note1 : L+1.2 max. for 16V270µF (Rated ripple current 5,080mArms).
âMARKING
EX) 16V150µF
G 6D6
150
16V
L'
15min.
4min.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
50
CAT. No. E1001Q
|
▷ |