APSF2R5ELL471 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
PSF NPCAP^TM-
Series
・Super low ESR, high ripple current capability
・ESR 5mΩmax. (2 to 4Vdc)
・Longer life (20,000 hours at 105℃)
・Rated voltage range : 2 to 16Vdc
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
PSF
Lower ESR
PSE P56
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
-55 to +105℃
2 to 16Vdc
±20%(M)
Rated voltage(V)×1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.10 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
2 to 6.3Vdc : ≦The initial specified value
16Vdc
: ≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
2 to 6.3Vdc : ≦The initial specified value
16Vdc
: ≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
●Terminal Code : E
F05, F08, H08 ^{Coated Case}
L'
FA5, HB5, JB5 ^{Coated Case}
15min.
4min.
(FA5)
(HB5, JB5)
Size code F05 F08 FA5 H08 HB5 JB5
φD
6.3
8.0
10.0
φd
0.45 0.6 0.5
0.6
F
2.5
3.5
5.0
φD'
φD+0.5max.
L' L+1.0max. (Note1) L+0.3max. L+1.0max. L+1.5max.
Note1 : L+1.2 max. for 6.3V820µF
◆MARKING
EX) 2.5V560µF
F ^6D6
560
2.5^V
L'
15min.
4min.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
54
CAT. No. E1001Q