|
APSF160ELL271 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS | |||
|
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
PSF NPCAPTM-
Series
ã»Super low ESR, high ripple current capability
ã»ESR 5mΩmax. (2 to 4Vdc)
ã»Longer life (20,000 hours at 105â)
ã»Rated voltage range : 2 to 16Vdc
ã»Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
ã»RoHS Compliant
ã»Halogen Free
PSF
Lower ESR
PSE P56
âSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
-55 to +105â
2 to 16Vdc
±20%(M)
Rated voltage(V)Ã1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20â, 120Hz)
(at 105â)
(at 20â after 2 minutes)
0.10 max.
(at 20â, 120Hz)
Z(-25â)/Z(+20â)â¦1.15
Z(-55â)/Z(+20â)â¦1.25
(at 100kHz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after the rated voltage is applied for 20,000 hours
at 105â.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjecting them to DC voltage at 60â,
90 to 95% RH for 1,000 hours.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦The initial speciï¬ed value
ESR
2 to 6.3Vdc : â¦The initial speciï¬ed value
16Vdc
: â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage speciï¬ed at 105â for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦The initial speciï¬ed value
ESR
2 to 6.3Vdc : â¦The initial speciï¬ed value
16Vdc
: â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
0.5% per 1,000 hours maximum (Conï¬dence level 60% at 105â)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105â.
âDIMENSIONS [mm]
âTerminal Code : E
F05, F08, H08 Coated Case
L'
FA5, HB5, JB5 Coated Case
15min.
4min.
(FA5)
(HB5, JB5)
Size code F05 F08 FA5 H08 HB5 JB5
ÏD
6.3
8.0
10.0
Ïd
0.45 0.6 0.5
0.6
F
2.5
3.5
5.0
ÏD'
ÏD+0.5max.
L' L+1.0max. (Note1) L+0.3max. L+1.0max. L+1.5max.
Note1 : L+1.2 max. for 6.3V820µF
âMARKING
EX) 2.5V560µF
F 6D6
560
2.5V
L'
15min.
4min.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
54
CAT. No. E1001Q
|
▷ |