APSE6R3ELL471 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – Engineering Bulletin

Engineering Bulletin No.795 / Apr.2008
Conductive Polymer
Aluminum Solid Capacitors
@Super low ESR, high ripple current capability
@Downsized from PSC series (F8B8L to F6.3B8L)
@Endurance is longer life than PSC series (5,000 hours at 105C)
@ESR after endurance is specified within the initial spec
@Rated voltage range : 2.5 to 6.3Vdc
@RoHS Compliant
@Halogen Free
Halogen ^Free
Downsized
Long ^Life
?SPECIFICATIONS
Items
Category
Temperature Range ^{-55 to +105C}
Characteristics
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Halogen Free
(Definition)
Failure Rate
2.5 to 6.3Vdc
P20% (M)
Rated voltage(V)B1.15
I=0.2CV or 500MA, whichever is greater
Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
0.10 max.
(at 20C, 120Hz)
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 5,000 hours
at 105C.
Appearance
No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)
[The initial specified value
ESR
[The initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)
[The initial specified value
ESR
[The initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change [P20% of the initial value
D.F. (tanE)
[The initial specified value
ESR
[The initial specified value
Leakage current
[The initial specified value
All homogeneous materials within a capacitor meet the criteria in Table-1 and Tabel-2.
Homogeneous material has uniform composition throughout and cannot be mechanically disjointed into different materials.
Table-1
Table-2
Substance
Permissible limit (by weight)
Substance
Permissible limit (by weight)
Bromine (Br)
Chlorine (Cl)
[900ppm (0.09%)
[900ppm (0.09%)
Antimony Trioxide (Sb2O3)
Red Phosphorus
[1,000ppm (0.10%)
[1,000ppm (0.10%)
Total concentration of
Chlorine (Cl) + Bromine (Br) ^{[1,500ppm (0.15%)}
0.5% per 1,000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS [mm]
@Terminal Code : E
Coated Case
Size code
fD
fd
F
fD'
L'
F08
6.3
0.6
2.5
FD+0.5max.
L+1.5max.
?MARKING
EX) 2.5V820MF
E ^6D6
820
2.5^V
L'
15min.
4min.
Specifications in this bulletin are subject to change without notice.
NIPPON CHEMI-CON CORPORATION
1435
1