|
APSC6R3ELL152 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS | |||
|
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
PSC NPCAPTM-
Series
ã»Super low ESR, high ripple current capability
ã»Lower profile than PSA (Ï8Ã8L to Ï10Ã12.5L)
ã»Rated voltage range : 2.5 to 16Vdc
ã»Nominal capacitance range : 270 to 2,700µF
ã»Endurance : 15,000 hours at 105â
ã»Suitable for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards
ã»Added 2.5V 820µF (ESR 5mΩ max.)
ã»Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
ã»RoHS Compliant
ã»Halogen Free
PSC
Low profile
Lower ESR
PSA P60
âSPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanÐ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
-55 to +105â
2.5 to 16Vdc
±20% (M)
Rated voltageÃ1.15
I=0.2CV or 500µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (Vdc)
(at 20â, 120Hz)
(at 105â)
(at 20â after 2 minutes)
0.10 max.
(at 20â, 120Hz)
Z(-25â)/Z(+20â)â¦1.15
Z(-55â)/Z(+20â)â¦1.25
(at 100kHz)
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after the rated voltage is applied for 15,000 hours
at 105â.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The following speciï¬cations shall be satisï¬ed when the capacitors are restored to 20â after subjecting them to DC voltage at 60â,
90 to 95% RH for 1,000 hours.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage speciï¬ed at 105â for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No signiï¬cant damage
Capacitance change
â¦Â±20% of the initial value
D.F. (tanδ)
â¦150% of the initial speciï¬ed value
ESR
â¦150% of the initial speciï¬ed value
Leakage current
â¦The initial speciï¬ed value
0.5% per 1,000 hours maximum (Conï¬dence level 60% at 105â)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105â.
âDIMENSIONS [mm]
âTerminal Code : E
Coated Case
L'
15min.
4min.
Size code H08
HB5
JB5
JC5
ÏD
8.0
8.0
10.0
10.0
Ïd
0.6
0.8(Note1) 0.8(Note1)
0.6
F
3.5
3.5
5.0
5.0
ÏD'
ÏD+0.5max.
L'
L+1.0max.
L+1.5max.
Note1 : 0.6 for rated volt 16V.
âMARKING
EX) 2.5V820µF
C 3D6
820
2.5V
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
58
CAT. No. E1001Q
|
▷ |