APSC160ELL331 Datasheet, PDF (1/2 Pages) United Chemi-Con, Inc. – CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Radial Lead
PSC NPCAP^TM-
Series
・Super low ESR, high ripple current capability
・Lower profile than PSA (φ8×8L to φ10×12.5L)
・Rated voltage range : 2.5 to 16Vdc
・Nominal capacitance range : 270 to 2,700µF
・Endurance : 15,000 hours at 105℃
・Suitable for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards
・Added 2.5V 820µF (ESR 5mΩ max.)
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
PSC
Low profile
Lower ESR
PSA P60
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Dissipation Factor
(tanЎ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
-55 to +105℃
2.5 to 16Vdc
±20% (M)
Rated voltage×1.15
I=0.2CV or 500µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (Vdc)
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.10 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 15,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
●Terminal Code : E
Coated Case
L'
15min.
4min.
Size code H08
HB5
JB5
JC5
φD
8.0
8.0
10.0
10.0
φd
0.6
0.8(Note1) 0.8(Note1)
0.6
F
3.5
3.5
5.0
5.0
φD'
φD+0.5max.
L'
L+1.0max.
L+1.5max.
Note1 : 0.6 for rated volt 16V.
◆MARKING
EX) 2.5V820µF
C ^3D6
820
2.5^V
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
58
CAT. No. E1001Q