UPG2183T6C Datasheet, PDF (4/13 Pages) California Eastern Labs – 4W HIGH POWER SP4T SWITCH

PG2183T6C
ELECTRICAL CHARACTERISTICS
(TA = +25C, Vbat = 3.0 V, VDD = 2.65 V, Vcont (H) = 2.65 V, Vcont (L) = 0 V, Zo = 50 , DC blocking
capacitors = 56 pF, unless otherwise specified)
Parameter
Insertion Loss 1
Insertion Loss 2
Insertion Loss 3
Isolation 1
Isolation 2
Isolation 3
Input Return Loss
Output Return Loss
0.1 dB Loss Compression
Input Power 1 ^Note
0.1 dB Loss Compression
Input Power 2 ^Note
Harmonics 1
Harmonics 2
Battery Current 1
Battery Current 2
Switched Supply Current 1
Switched Supply Current 2
Control Current 1-1
Control Current 1-2
Control Current 2-1
Control Current 2-2
Switch Control Speed
Startup Time
Symbol
Test Conditions
Lins1 f = 0.5 to 1.0 GHz
Lins2 f = 1.0 to 2.0 GHz
Lins3 f = 2.0 to 2.5 GHz
ISL1 f = 0.5 to 1.0 GHz
ISL2 f = 1.0 to 2.0 GHz
ISL3 f = 2.0 to 2.5 GHz
RLin f = 0.5 to 2.5 GHz
RLout f = 0.5 to 2.5 GHz
Pin (0.1 dB) 1 f = 0.9 GHz
MIN.



22
17
15
15
15
+37.0
TYP.
0.4
0.55
0.7
24
19
17
19
19
+37.5
MAX.
0.55
0.8
0.95






Unit
dB
dB
dB
dB
dB
dB
dB
dB
dBm
Pin (0.1 dB) 2 f = 1.8 GHz
+34.0 +35.0

dBm
2f0 f = 0.9 GHz, Pin = 34.5 dBm

75
65
dBc
3f0

75
65
dBc
2f0 f = 1.8 GHz, Pin = 31.5 dBm

72
62
dBc
3f0

75
62
dBc
Ibat1 Active Mode, No RF

0.55
1.5
mA
Ibat2 Standby Mode, No RF


10
A
IDD1 VDD : High, No RF

0
0.1
mA
IDD2 VDD :Low, No RF

0
0.1
mA
Icont 1-1 Vcont1 : High, No RF
100
0
100
A
Icont 1-2 Vcont1 : Low, No RF
100
0
100
A
Icont 2-1 Vcont2 : High, No RF
100
0
100
A
Icont 2-2 Vcont2 : Low, No RF
100
0
100
A
tSW 50% CTL to 90/10%

0.5
5.0
s

Time for the switch to be operational

from that the switched supply voltage
(VDD) goes high.

100
s
Note Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear
range.
Caution This device is used it is necessary to use DC blocking capacitors.
The value of DC blocking capacitors should be chosen to accommodate the frequency of
operation, bandwidth, switching speed and the condition with actual board of your system. The
range of recommended DC blocking capacitor value is less than 56 pF.
4
Data Sheet PG10762EJ01V0DS