UPG2406TK_09 Datasheet, PDF (3/12 Pages) California Eastern Labs – 0.01 to 3.0 GHz SPDT SWITCH

PG2406TK
ELECTRICAL CHARACTERISTICS
(TA = +25C, Vcont (H) = 2.7 V, Vcont (L) = 0 V, DC blocking capacitors = 56 pF, unless otherwise
specified)
Parameter
Insertion Loss 1
Insertion Loss 2
Insertion Loss 3
Insertion Loss 4
Insertion Loss 5
Insertion Loss 6
Isolation 1
Isolation 2
Isolation 3
Isolation 4
Isolation 5
Isolation 6
Input Return Loss 1
Input Return Loss 2
Input Return Loss 3
Output Return Loss 1
Output Return Loss 2
Output Return Loss 3
0.1 dB Loss Compression
Input Power ^{Note 3}
1 dB Loss Compression
Input Power ^{Note 4}
2nd Harmonics
3rd Harmonics
Intermodulation Intercept Point
Switch Control Current
Switch Control Speed
Symbol
Test Conditions
Lins1
Lins2
f = 0.01 to 0.05 GHz ^{Note 1}
f = 0.05 to 0.5 GHz ^{Note 2}
Lins3 f = 0.5 to 1.0 GHz
Lins4 f = 1.0 to 2.0 GHz
Lins5 f = 2.0 to 2.5 GHz
Lins6
ISL1
ISL2
f = 2.5 to 3.0 GHz
f = 0.01 to 0.05 GHz ^{Note 1}
f = 0.05 to 0.5 GHz ^{Note 2}
ISL3 f = 0.5 to 1.0 GHz
ISL4 f = 1.0 to 2.0 GHz
ISL5 f = 2.0 to 2.5 GHz
ISL6
RLin1
RLin2
f = 2.5 to 3.0 GHz
f = 0.01 to 0.05 GHz ^{Note 1}
f = 0.05 to 0.5 GHz ^{Note 2}
RLin3
RLout1
RLout2
f = 0.5 to 3.0 GHz
f = 0.01 to 0.05 GHz ^{Note 1}
f = 0.05 to 0.5 GHz ^{Note 2}
RLout3 f = 0.5 to 3.0 GHz
Pin (0.1 dB) f = 2.0/2.5 GHz
f = 0.5 to 3.0 GHz
Pin (1 dB) f = 0.5 to 3.0 GHz
2f0 f = 2.0/2.5 GHz, Pin = +20 dBm
3f0 f = 2.0/2.5 GHz, Pin = +20 dBm
IIP3 f = 0.5 to 3.0 GHz, 2 tone,
5 MHz spicing
Icont No RF input
tSW 50% CTL to 90/10% RF
MIN.







23
23
16
14
14

15
15

15
15
+26.0


TYP.
0.40
0.40
0.40
0.45
0.47
0.53
27
27
27
19
17
17
20
20
20
20
20
20
+29.0
+29.0
+30.5
MAX.

0.45
0.45
0.50
0.55
0.60















Unit
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dBm
dBm
dBm
65
75
65
75

+60

dBc

dBc

dBm

0.2
20
A

50
500
ns
Notes 1. DC blocking capacitors = 10 000 pF at f = 0.01 to 0.05 GHz
2. DC blocking capacitors = 1 000 pF at f = 0.05 to 0.5 GHz
3. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of
linear range.
4. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of
linear range.
Caution This device is used it is necessary to use DC blocking capacitors.
The value of DC blocking capacitors should be chosen to accommodate the frequency of
operation, bandwidth, switching speed and the condition with actual board of your system. The
range of recommended DC blocking capacitor value is less than 56 pF.
Data Sheet PG10746EJ01V0DS
3