UPC3217GV Datasheet, PDF (1/8 Pages) NEC – NECs GENERAL PURPOSE 5 V AGC AMPLIFIER

5 V AGC AMPLIFIER + UPC3217GV
VIDEO AMPLIFIER ^UPC3218GV
FEATURES
• ON-CHIP LOW DISTORTION AMPLIFIER:
IIP3 = -4 dBm at minimuim gain
• WIDE AGC DYNAMIC RANGE:
GCR = 53 dB TYP
• ON-CHIP VIDEO AMPLIFIER:
VOUT = 1.25 VP-P at single-ended output
• SUPPLY VOLTAGE:
VCC = 5 V
• PACKAGED IN 8 PIN SSOP SUITABLE FOR
SURFACE MOUNTING
DESCRIPTION
NEC's UPC3217GV and UPC3218GV are Silicon Monolithic
ICs designed for use as AGC amplifiers for digital CATV,
cable modems and IP telephony systems. These ICs con-
sist of a two stage gain control amplifier and a fixed video
gain amplifier. The devices provide a differential input and
differential output for noise performance, which eliminates
shielding requirements.
The package is 8-pin SSOP (Shrink Small Outline Package)
suitable for surface mount.
These ICs are manufactured using NEC's 10 GHz fT
NESATΙΙ AL silicon bipolar process. This process uses
silicon nitride passivation film. This material can protect chip
surface from external pollution and prevent corrosion/migra-
tion. Thus, these ICs have excellent performance, uniformity
and reliability.
NEC's stringent quality assurance and test procedures ensure
the highest reliability and performance.
VOLTAGE GAIN vs.
AUTOMATIC GAIN CONTROL VOLTAGE*
UPC3217GV
Automatic Gain Control Voltage, VAGC* (V)
UPC3218GV
Automatic Gain Control Voltage, VAGC* (V)
APPLICATIONS
•Digital CATV
• Cable modem receivers
• IP Telephony Receivers
ELECTRICAL CHARACTERISTICS
(TA = 25°C, VCC = 5 V, ZS = 1 K Ω, ZL = 240 Ω, fIN = 45 MHz, Unless otherwise specified)
PART NUMBER
PACKAGE OUTLINE
SYMBOLS
PARAMETERS AND CONDITIONS
DC Characteristics
ICC
Circuit Current (no input signal)
RF Characterisitics
BW
Frequency Bandwidth, VAGC* = 4.5 V¹
GMAX
Maximum Gain , VAGC* = 4.5 V
GMIN
Minimum Gain, VAGC* = 0.5 V
GCR
Gain ConTrol Range, VAGC* = 0.5 to 4.5 V
NFAGC
Noise Figure, VAGC* = 4.5 V at MAX Gain
VOUT
Output Voltage, Single Ended Output
IM3
Third Order Intermodulation Distortion,

fIN1 = 44 MHz, fIN2 = 45 MHz,

VIN = 30 dBmV per tone²
Note:
1. -3dB with respect to 10 MHz gain
2. VAGC is adjusted to establish VOUT = 1.25 VP-P per tone
UNITS
UPC3217GV
S08
MIN TYP
MAX
UPC3218GV
S08
MIN
TYP
MAX
mA
15
MHz
dB
50
dB
-4.5
dB
46.5
dB
VP-P
dBc
23
34
15
100
53
56
60
0
3.5
4.5
53
46.5
6.5
8.0
1.25
55
23
34
100
63
66
10
13.5
53
3.5
4.5
1.25
55
California Eastern Laboratories
* VAGC shown as applied in the evaluation cicuit (see page 5) through a resistive bridge (voltage divider).
Actual voltage range on the pin of the IC is 0 to 3 V.