UPA811T_09 Datasheet, PDF (1/3 Pages) California Eastern Labs – NPN SILICON HIGH

SILICON TRANSISTOR
UPA811T
NPN SILICON HIGH
FREQUENCY TRANSISTOR
FEATURES
OUTLINE DIMENSIONS (Units in mm)
• SMALL PACKAGE STYLE:
2 NE680 Die in a 2 mm x 1.25 mm package
• LOW NOISE FIGURE:
NF = 1.9 dB TYP at 2 GHz
• HIGH GAIN:
|S21E|² = 7.5 dB TYP at 2 GHz
• EXCELLENT LOW VOLTAGE, LOW CURRENT
PERFORMANCE
DESCRIPTION
The UPA811T is two NPN high frequency silicon epitaxial
transistors encapsulated in an ultra small 6 pin SMT package.
Each transistor is independently mounted and easily config-
ured for either dual transistor or cascode operation. The high
fT, low voltage bias and small size make this device ideally
suited for pager and other hand-held wireless applications.
ABSOLUTE MAXIMUM RATINGS¹ (TA = 25°C)
SYMBOLS
PARAMETERS
UNITS RATINGS
VCBO Collector to Base Voltage
V
20
VCEO Collector to Emitter Voltage V
10
VEBO Emitter to Base Voltage
V
1.5
IC
Collector Current
mA
35
PT
Total Power Dissipation
1 Die
mW
110
2 Die
mW
200
TJ
Junction Temperature
°C
150
TSTG Storage Temperature
°C
-65 to +150
Note:
1. Operation in excess of any one of these parameters may result
in permanent damage.
PACKAGE OUTLINE S06
(Top View)
2.1 ± 0.1
1.25 ± 0.1
0.65 ¹
2.0 ± 0.2
1.3
2
3
6
0.2 (All Leads)
5
4
0.9 ± 0.1
0.7
0 ~ 0.1
0.15
+0.10
- 0.05
PIN OUT
1. Collector Transistor 1
2. Base Transistor 2
3. Collector Transistor 2
4. Emitter Transistor 2
5. Emitter Transistor 1
6. Base Transistor 1
Note:
Pin 3 is identified with a circle on the bottom of the package.
ELECTRICAL CHARACTERISTICS (TA = 25°C)
PART NUMBER
PACKAGE OUTLINE
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
ICBO
Collector Cutoff Current at VCB = 10 V, IE = 0
μA
IEBO
hFE1
Emitter Cutoff Current at VEB = 1 V, IC = 0
Forward Current Gain at VCE = 3 V, IC = 5 mA
μA
80
fT
Gain Bandwidth at VCE = 3 V, IC = 5 mA
GHz
5.5
Cre²
Feedback Capacitance at VCB = 3 V, IE = 0, f = 1 MHz
pF
|S21E|² Insertion Power Gain at VCE = 3 V, IC = 5 mA, f = 2 GHz
dB
5.5
NF
Noise Figure at VCE = 3 V, IC = 5 mA, f = 2 GHz
dB
Notes:
1.Pulsed measurement, pulse width ≤ 350 μs, duty cycle ≤ 2 %.
2.The emitter terminal should be connected to the ground terminal of the 3 terminal capacitance bridge.
For Tape and Reel version use part number UPA811T-T1, 3K per reel.
UPA811T
S06
TYP
120
8.0
0.3
7.5
1.9
MAX
1.0
1.0
200
0.7
3.2