VR1B Datasheet, PDF (1/3 Pages) Cornell Dubilier Electronics – Type VR Vertical Mounting Clamp, Type TH Horizontal Mounting Clip

Type VR Vertical Mounting Clamp
Capacitor Hardware
CDE VR mounting clamps may be
used to mount any cylindrical ca-
pacitor with a 1” to 3” diameter
that is to be mounted in a verti-
cal position. Material is 1010 CRS,
commercial grade #4 temper ASI
scale. Parts are finished with .0001
(nominal) zinc chromate plating.
Use for mounting CG types, PSU, SF
and MPF types. Material thickness
is .035”
Diameter
of Part to be
Mounted
1" to 1-1/16
1-3/8" to 1-7/16
1-1/2" to 1-9/16
1-3/4" to 1-13/16
2" to 2-1/16
2-1/2" to 2-9/16
3" to 3-1/8
Screw
Nut
Catalog Part Number
Unassembled Assembled
Without
Screw & Nut
with
Screw & Nut
Included
Screw & Nut
VR1B
VR1
VR1A
VR3B
VR3
VR3A
VR4B
VR4
VR4A
VR6B
VR6
VR6A
VR8B
VR8
VR8A
VR10B
VR10
VR10A
VR12B
VR12
VR12A
VRSCREW
—
—
VRNUT
—
—
Dimensions
A
B
C
1"
1-7/16" 1-7/8*"
1-3/8" 1-25/32" 2-7/32"
1-1/2" 1-15/16" 2-11/32"
1-3/4" 2-1/4" 2-9/16"
2"
2-1/2" 2-13/16"
2-1/2" 3"
3-5/16"
3"
3-7/16" 3-13/16"
9/16" long 6-32 thread NC-2A
Standard hex nut to fit screws
VR1, 3 & 4
.219”
.375”
B Mtg
2 Holes
.1561” Dia.
.156”
.562” _.750”
VR6, 8,10 & 12
C ±0.01”
B Mtng ±0.03”
0.176” x 0.281”
±0.016 (3 places).
120 º ±3 º
0.01.8384”4±” ^{±0.00.1061”6”}
(3 Places)
75 º
A ±0.016”
B Mtng ±0.03”
Ø 0.201” ±0.005”
Type TH Horizontal Mounting Clip
1.125” ±0.016”
0.375”±0.016”
Catalog
Part Number
TH17
TH25
Material Thickness
TH17 is 0.016”, TH25
is 0.025”.
Material: 1050 high
carbon steel with
Retaining tabs
must extend ^{Retaining tabs must}
extend lower
lower^tht^ahⁿ a^ban^seb^ofa^cs^lipe
of clip
phosphate and oil
finish. TH25 is 1060.
Dimensions in Inches
Nominal Dia.
of Part to be
0.035”
0.075” ±0.016”
0.500” ±0.016”
Mounted
0.625
1.375
A
B
C
0.312 0.720 0.015
0.312 1.500 0.030
Added tolerance to "C" dim.
(*) 0.340” execpt TH25 is 0.590”
(*)
(*) 0.340" except TH25 is 0.590".
These clips, though designed for
capacitors, have varied applica-
tions to retain many cylindrical
components. They are used ex-
tensively in the electrical and elec-
tronic industries to hold spindles,
condensers, capacitors, tubes,
B
rods and conduit. Clips have phos-
phate and oil finish.
C ±0.010"
Material thickness TH13 thru TH17
is .016”. TH21 thru TH25 is .020”
A
0.594"
0₀._.1₁3₃5₅" _”D_Dia_i._aH_.o_Hle_ole
ACR15KT Motor Start Resistor Kit
ACR220KT Motor Run Resistor Kit
15K Ohm 2 watt bleeder resistors for AC motor start applica-
tions. Saves relay switch contacts and capacitor, particularly in
capacitor start applications. 1/4” quick connect terminals elimi-
nate need for soldering.
220K Ohm 1 watt bleeder resistors for AC motor run applica-
tions. Saves relay switch contacts and capacitor, particularly in
capacitor run applications. 1/4” quick connect terminals elimi-
nate need for soldering.
ACR15K:
ACR220K:
Pack of 10, 15K Ohm 2 watt bleeder resistor without quick con- Pack of 10, 220K Ohm 1 watt bleeder resistor without quick con-
nect terminals.
nect terminals.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: [phone] • Fax: [phone] • www.cde.com